otis 故障代码（奥的斯故障代码）.doc

otis 故障代码（奥的斯故障代码） otis xizi otis 21vf / 故障代码表mcs321 / 故障代码表toec2000 / 故障代码表300vf 故障代码表 1100 software reset 软件复位 1101 ring software reset 群控软件复位 1200 sio message framing error 从mcss接受到的数据信息中检测到结构错误 1201 sio timeout error 与mcss通讯超时 1300 rsl1 loss of synchronization 轿厢通讯收发不同步 1301 rsl2 loss of synchronization 厅外通讯收发不同步 1302 rsl3 loss of synchronization 群控通讯收发不同步 1400 rsl1 total parity errors 轿厢通讯出现奇偶校验错误 1401 rsl2 total parity errors 厅外通讯出现奇偶校验错误 1402 rsl3 total 群控通讯出现奇偶校 parity errors 验错误 1500 ring1 checksum error 群控环1通讯有检测故障 1501 ring1 timeout error 群控环1通讯有超时故障 1700 mcss not available mcss通讯故障 1701 car shutdown while in epo 备用电源操作时出现故障 1702 dtc protection count dtc关门保护 1703 dto protection count dto关门保护 1704 delay car protection dcp保护 1800 efo - p and efo ck are invalid or do not match 消防楼层参数错误或efo - p与efo - ck不一致或该层门被封 1801 asl - p and asl. ck are invalid or do not match 消防可选楼层参数错误或asl - p与asl - ck不一致或该层门被封 efs efs and ck are invalid or do not match 消防类型参数错误或efs与efs - ck不一 致 asl2 - p and asl2 ck are invalid or do not match 消防第二可选楼层参数错误或asl2 - p与asl2 - ck不一致或该层门被封 1804 rcbii电池电压不足 1805 eqo hoistway sensor failed 地震井道传感器故障 1806 invalid eqo parameter setup 无效的地震参数 1807 car is configured for random calls 电梯由随机内外呼控制运行 故障代码 服务器显示 说 明 2000 stm software reset 电子板软件运行错误, 引起cpu复位. 2001 stm power on reset 上电复位, 或者按了复位按钮 2002 stm. power fail 5v电源的电压低于2.5v.在系统失电期间, 系统停机. 2005 stm not availabl e 某些非正常状态被mcss检测到, 这时应查其他故障记录.另外, This record is also in emergency or repair 2100, PSR, Big, POS, slip, and the elevator running in line with the direction of the rope slippage is too large. 2101, PSR, Big, neg, slip, and the elevator running in the opposite direction of the wire rope slippage is too large. 2102 PSR Pos MES FLT PVT read position has been located in the flat floor area, but no DZ input, should check the floor count of 2103 PSR Inv. A FLOOR COUNT is invalid, the floor count and actual wells floors are not consistent, or beyond the highest or lowest floor limit. Occurs in the