卓异卫星接收机维修实例（Good maintenance examples of satellite receiver）.docVIP

下载本文档

5
0
约8.41千字
约 6页
2017-09-07 发布于河南
举报
版权申诉

卓异卫星接收机维修实例（Good maintenance examples of satellite receiver）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

卓异卫星接收机维修实例（Good maintenance examples of satellite receiver）

卓异卫星接收机维修实例（Good maintenance examples of satellite receiver） 1, a good 9 receiver power without reflection, disassemble the detection power supply inductance bad power module Q100 peripheral circuit according to the bad Xun, 6, 7, 8 feet by 1 feet, transformer, 2 foot Vcc, 3 feet by 4 feet by optocoupler, grounding resistance 4.7K, 5 feet by 300V. The data were similar to DH321. Successful repair with dh321 direct substitution. 2, 2250 outstanding small general receiver, after the start of television shows no signal. View signal, signal quality and signal strength are zero. The user informs that the manual RF input block is normal. Open the shell and press ZL10036 by hand. Sometimes it can be normal. After ZL10036 welding, it is normal, but there is no signal for second days. Therefore, the IC base plate is repaired and welded to the lead, and the result has been normal. Because of the ZY10036 when the temperature is very high, the copper yellow IC floor, and the pin is very short, it is easy to form. It is worth noting that the author has repaired many such machines. 3, models and faults ibid. However, when viewing the information, the signal quality is 1% and the signal strength is 95%. ZL10036 by hand is sometimes normal. ZY10036 repair welding invalid, with oscilloscope measuring XTAL3 at both ends without waveform, the XTAL3 crystal welding repair all normal. The crystal and the failure can be bad. 4, a good ZY 5518AH nine machine boot after the front panel has no display, no map. Silent boot after the front panel without any display, should first check the power supply fault. The measured voltage switching power supply were no output. Check the bridge rectifier circuit after both ends of filter capacitor C901 300V DC voltage, fault should occur the AC power input and rectifier filter circuit, the bridge rectifier circuit in D901 (IN5399) has breakdown. According to the maintenance experience, rectifier breakdown will cause the AC power input fuse fuse, but thi