智能探测器技术知识问答（Intelligent detector technology Knowledge Q A）.docVIP

下载本文档

0
0
约1.97万字
约 16页
2017-09-07 发布于河南
举报
版权申诉

智能探测器技术知识问答（Intelligent detector technology Knowledge Q A）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

智能探测器技术知识问答（IntelligentdetectortechnologyKnowledgeQ

智能探测器技术知识问答（Intelligent detector technology Knowledge Q A） The same trigger detector to transmit an alarm signal, if not set the power-saving mode, the detector does not stop detection after launch, is a large power consumption, battery loss quickly, causing the user cost increase and often need to replace the battery, not up to the economic and effective security purposes. Eight. Why should infrared detectors be designed for 1 minutes in normal mode? Answer: infrared detector has 1 minutes induction time in the surrounding environment when the switch is closed, and then enter the normal working state, when it transmits the alarm signals after induction of human intrusion, due to high power transmitter battery voltage low, the supply to the detector CPU working voltage is not stable, at this time, such as let the detector may work immediately detection. Incorrect judgment and false positives. According to the working principle of infrared detector circuit, the detector successfully launches an alarm signal and takes about 30 seconds to recover the voltage and time. So we developed the intelligent detector of normal working hours for a minimum of 1 minutes, therefore, require customers to using power saving mode or normal mode when in normal use, with a test pattern (10 seconds) cannot work normally, to reduce the false positives generated. Nine, why infrared detectors use 6V power supply? And the benefits of stopping work at low voltage? Answer: due to the working voltage of CPU is 3V, in order to make the voltage fluctuations do not affect the normal operation of the CPU generated false positives, the use of 6V power supply mode. When the voltage is low to a certain extent, but at higher than 3V, the CPU will cause the detector to stop working. The advantage is to prevent infrared detector from low voltage fluctuation or insufficient power supply caused by false positives. Ten, the infrared detector power-saving mode is how to achieve? After successful alarm, can