数控铣床工作台设计（Design of worktable for NC milling machine）.docVIP

下载本文档

2
0
约9.75千字
约 7页
2017-09-15 发布于河南
举报
版权申诉

数控铣床工作台设计（Design of worktable for NC milling machine）.doc

1、本文档共7页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

数控铣床工作台设计（Design of worktable for NC milling machine）

数控铣床工作台设计（Design of worktable for NC milling machine） Introduction of five axis machining center and its difference from three axis and four axis Vertical machining center (three axis) the most effective processing surface is only the top surface of the workpiece, and the horizontal machining center with the aid of the rotary table can only complete the four sides processing of the workpiece. At present, the advanced machining center is developing in the direction of five axis control, and the workpiece can be finished with five sides at one time. Such as the configuration of five axis linkage of high-end CNC system, you can also complex space surface high-precision machining. Vertical five axis machining center There are two ways of turning the shaft in this kind of machining center. One is the back of the work table. The worktable set on the bed can be pivoted around the X axis, defined as the A axis, and the A axis generally ranges from +30 degrees to -120 degrees. There is also a turret in the center of the table, which rotates on the Z axis at the position shown. It is defined as the C axis, and the C axis is 360 degree rotation. Thus, through the combination of the A shaft and the C shaft, the workpiece on the worktable is in addition to the bottom surface, and the remaining five surfaces can be processed by a vertical spindle. A axis and C axis minimum division value is generally 0.001 degrees, so that the workpiece can be subdivided into any angle, processing inclined surface, tilt hole, etc.. A axis and C axis, such as linkage with the XYZ three linear axis, can be processed complex space curved surface, of course, this requires high-grade CNC systems, servo systems and software support. The advantage of this set way is that the structure of the spindle is relatively simple, the rigidity of the spindle is very good, and the manufacturing cost is relatively low. But the general work platform can not be designed too large, and the bearing capacity is smaller,