第六章互换性（The sixth chapter is interchangeability）.docVIP

下载本文档

12
0
约7.09千字
约 7页
2017-09-28 发布于河南
举报
版权申诉

第六章互换性（The sixth chapter is interchangeability）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

第六章互换性（The sixth chapter is interchangeability）

第六章互换性（The sixth chapter is interchangeability） The sixth chapter is the design of smooth limit gauge I. judgment questions (correctly written T, wrongly written F) 1. The smooth limit gauge is a non metric checker for the inspection of the size and shape of a smooth workpiece based on the inclusion principle. T 2. The basic size of the gauge gauge is equal to the maximum limit size of the workpiece. F 3. The gauge is used to control the actual size of the workpiece, not exceeding the maximum physical size. F 4, the inspection hole size is qualified gauge is pass, check the shaft size is qualified, gauge is stop gauge. F 5, plug is limit gauge hole for inspection, the rules it is based on the minimum limit of size design of hole. T 6. The ring gauge is the limit gauge used to inspect the shaft. The gauge is designed according to the minimum limit of the shaft. F Check gauge 7, gauge is designed according to the maximum limit of size of shaft, the role is to prevent the maximum limit of size greater than the actual size of the shaft axis. F 8 the gauge used to inspect the work gauge is the calibration gauge. T The working face 9, plug should be wide, the gauge should be punctual. F 10. The tolerances for pass and gauge tolerances consist of two parts, the manufacturing tolerances and the wear tolerances. F 11. The wear allowance of gauge is to increase the manufacturing tolerance of gauge and make gauge easy to process. F 12, the specified position elements of Z is to ensure that the plug has certain service life. T 13, the national standard stipulates that the work gauges use the internal shrinkage limit. T 14, safety margin by measurement uncertainty is determined. F 15, the acceptance limit is the maximum limit of size and the minimum limit of size reduction respectively to a safety margin of A. F Two, Jane answer 1 test the function and classification of smooth limit gauges. Answer: in mass production, in order to improve product quality and inspection efficiency