卫浴设备安装施工及质量评定(Installation, construction and quality evaluation of bathroom equipment).docVIP

卫浴设备安装施工及质量评定(Installation, construction and quality evaluation of bathroom equipment).doc

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  4. 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  5. 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  6. 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  7. 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
卫浴设备安装施工及质量评定(Installation, construction and quality evaluation of bathroom equipment)

卫浴设备安装施工及质量评定(Installation, construction and quality evaluation of bathroom equipment) Installation, construction and quality evaluation of bathroom equipment Installation, construction and quality evaluation of bathroom equipment 1, washbasin installation method Install pipe rack, wash basin, according to the center of the nozzle to draw water from the ground to the vertical line, on the amount of provisions Height, draw a line across the wall, mark the wall according to the width of the basin, and place a depth of 120mm in diameter Hole. Water is used to scour debris and other debris in the tunnel. The expansion bolt is inserted into the hole and twisted with cement Hang pot pipe fittings, rubber gasket, bolt circles, with nut is screwed to the appropriate degree of pipe end More than the basin fixing hole. Place the basin on the rack and level the bolts with a diameter of 4mm The upper end of the utility model is inserted into the fixing hole, and the lower end is inserted into the pipe hole, and the nut is screwed into the fitting hole Check. Launching connection. The basin and direct trap water connection, the first thread in the basin water outlet end Put a little oil lead, wrapped twine, the sewage pipe is screwed on the water outlet section, snug fit. Save the water again The lower end of the bent joint is wrapped with a whetstone and the cotton rope is inserted into the water inlet, and the rubber pad is placed at the connection point of the water retaining bend The mother hand tighten, and then Higuchi Sako put the nut to a snug fit, straightening is used after the putty The pipe stopper is tightly smoothed. The basin and eight trap water connected to water outlet in the basin under the first thread End with lead oil, a small amount of water will be wrapped around the twine, riser section is screwed on the water outlet, then the cross section according to the trap The length should be well matched, and the nut and the protecting mouth will be back to back

您可能关注的文档

文档评论(0)

f8r9t5c + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

版权声明书
用户编号:8000054077000003

1亿VIP精品文档

相关文档