冬季管道施工方案Rev.0.docVIP

Corning Display Technologies (China)Co.Ltd Phase Ⅱ 康宁显示科技（中国）二期 winter 冬季管道施工方案 （Rev.0） Establishment 编制 XXX Review 审核 Approve 批准 date 日期 2011-12-13 工程概况General 康宁显示科技（中国）有限公司第二期项目，MEPI(CUPOSBL), 管道工程主要包括冷冻水，冷却水系统，热水系统，压缩空气系统，柴油储存供应系统，天然气，氮气，氧气，液化石油气系统等。 Beijing Corning Phase II project MEPI(CUPOSBL) piping engineering include CTWS,CHWS, HW, CDA, DFS, DFR, NG, N2, O2 and LPG etc. 北京亦庄开发区属温带季风气候年平均气温在11.4~12.91月最冷，平均气温在-3~-5；季风盛行，冬、春季风速最大，年平均风速为2~4米/秒，多为西南风Industry Park belongs to the monsoon climate, annual average temperature is around 11.4 ~ 12.9 ℃. January is the coldest month, with an average temperature of -3 ~ -5 ℃. Monsoon prevails in Beijing. The largest wind speed is in spring and winter, the annual average wind speed of 2 ~ 4 m / s, mostly south-west winds. 编制目的Purpose 1、加强冬期施工技术管理，提高技术管理水平。 Strengthen and improve construction technology management in winter. 2、确保施工质量，避免由于技术措施不当引起不必要的返工、返修、资源浪费。 To ensure construction quality, avoiding unnecessary rework, repair, waste of resources. 3、确保施工安全，达到国家、地方、业主规定的目标。 To confirm construction safety and meet national, local, owner stated targets. 4、采取正确的冬期施工技术措施，有效降低工程成本，提高经济效益。 Take right construction technical measures in winter to reduce the project cost and increase economic efficiency. 三、施工技术措施Construction technical measures 1、管道焊接Piping Welding 当室外温度低于0℃，所有钢材的焊缝应在始焊处100cm范围内预热到15℃以上，防止因低温而导致焊接质量下降。在本项目，碳钢管线，我们将采取氧乙炔火焰预热进行加温，由于北京冬季气温较低，空气干燥，风速较大，为减少热量的散失，在各个焊接点搭设防风棚，防风棚的大小应能方便焊工操作，管内穿堂风用帆布包扎管口进行预防，完成预热后应立即进行管道焊接，为了确保层间温度，每层焊道必须紧凑，前一道工序完成后，立即进行下道工序。在每层焊道焊接前，需使用电子温度计测量管道温度是否符合规范要求，如过低，采用电加热器重新预热。 When the outdoor temperature is below 0℃, all weld seams shall be preheated above 15℃.In this project, we will take oxyacetylene flame for preheating. Due to low temperatures, dry air and larger wind speed in winter in Beijing, in order to reduce heat dissipation, wind shelters shall be put up in various welding points. The size of wind shelter should be able to facilitate welding. Cover nozzles by canvas for pre