Mercury G3 Service Tool Training Overview：汞G3服务工具的培训概述.pptVIP

下载本文档

8
0
约5.17千字
约 51页
2018-04-12 发布于江西
举报
版权申诉

Mercury G3 Service Tool Training Overview：汞G3服务工具的培训概述.ppt

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Mercury G3 Service Tool Training Overview：汞G3服务工具的培训概述.ppt

Mercury G3 Service Tool Training Overview Once Helm Config is completed, you will do a steering wheel adapt. If steering wheel adapt is not completed before Drive Initialization a WheelposAbsolute_Diff Fault may appear. Select # of engines by selecting drop down box # of Helms then Next Select Helm # and proceed in this slide there is no CCM online so process is not allowed Trackpad Configuration will allow you to see current City ID locations as well as reconfigure the City ID locations Once in Trackpad Configuration it will show you current trackpads on CAN P and CAN H with City ID’s. You can retore city id or assign track pads to new city ID’s. All ERC Track pads are on CAN P while Axius Precision Pilot screens are on CAN H * Mercury G3 Service Tool Training Overview Connect your G3 cable USB to computer and install drivers so cable can communicate with G3 If connecting to Axius or Zeus models, connect the 10 Pin on the G3 cable to the standard 6 or 8 way junction box for communication. On Axius it could also be plugged into the 10 Pin engine connection by removing the weather cap. (Yellow resistor on DTS engines) EC Engine connections, remove Yellow terminator resistor on engine harness. Use a 10 pin female to female connection to a 4 way J-box, install Yellow terminator from engine harness on to 4 way J-box. Female to female adaptor from 4 way to engine harness and G3 cable plugs into 4 way. You must keep the terminators on the CAN bus! When opening G3 you will start at this screen first import thing to look for is communication Red lights on both CAN P and CAN H indicate that the cable is not detected by G3 (check connection at USB on Computer) Yellow lights on CAN P and CAN H indicate the cable is detected but no response from Modules on CAN bus. Check power supply Cable Connection problem One CAN Bus is not detected in cable. Check Settings on Cable look at following slide. Click on YES to change options this will allow channel change on CAN H since it show