钣金理论部分试题（Examination questions of sheet metal theory）.docVIP

下载本文档

3
0
约1.93万字
约 11页
2018-06-16 发布于江西
举报
版权申诉

钣金理论部分试题（Examination questions of sheet metal theory）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

钣金理论部分试题（Examination questions of sheet metal theory）.doc

钣金理论部分试题（Examination questions of sheet metal theory） Sheet metal theory part of the examination questions A Volume 1, the body with the two types of steel is low carbon steel and high carbon steel. (x) 2. The ability of metal to extend and revert to its original shape is called plastic deformation. (x) 3, the door guard beam and bumper stiffener are not suitable for correction, should be replaced. (V) 4, bending or processed parts of the metal will be hardening. (V) in 5, repair the car, most of our work is in direct injury repair. (x) 6. When correcting the hinge break, the two sides should be alternately corrected from the top of the uplift to the highest point. (V) 7, a metal plate with a sunken, correction tapping hammers at the iron pad on the application. (x) 8. When the dent is repaired, it should begin to flatten out from the inside until the edge. (x) 9. When metal is used for metal tapping, the hammer is used on the iron pad. (V) 10, metal plate is pushed up the area is known as the compression zone was pulled down the area known as the stretch zone. (V) 11, damaged all the uplift on the metal plate should be corrected, should not use plastic filler. (V) 12, in all parts of the sag and uplift all beat down beat, and ultimately make the metal flat. (V) 13, now the structure of two kinds of common body is the frame body and whole body. (V) 14, integral body structure is divided into front, front and rear drive. (x) 15, now the main form of frame body is X frame. (x) 16, frame body collision, a large amount of energy absorbed by the frame. (V) 17, the integral strength of body parts from the stiffness and thickness. (x) 18, front engine buckle wheel drive and front wheel drive engine support method is the same. (V) 19, regardless of the frame body or the whole body strength, the highest part in the front of the car. (V) 20, a front wheel drive car front body and a rear wheel drive car the strength is different. (V) of 21, rear wheel positioning in the rear c