JJG 焊接检验尺检定规程.docxVIP

JJG 704- 2005 焊接检验尺检定规程 广0.0.O.O.0.O.O..0.口.O.0.O.O.0. JJG 704-2005 VeribzfxwicationRegulationof代替JJG704-1990 CalipersforWeldingInspection 本规程经国家质量监督检验检疫总局于 2005年 3月 3日批 准，并自2005年9月3日起施行。 归 口 单 位:全国几何量工程参量计量技术委员会主要起草单位:陕西省计量测试研究所参加起草单位:西安建筑科技大学 本规程委托全国几何量工程参量计量技术委员会负责解释 JJG 704- 2005 目 录 . 1 范围·.................................................... .......(1) 2 引用文献·····························，··························?? (1) 3 概述··········································，·················?? (1) 4 计量性能要求····················································?? (1) 4.1 高度尺、咬边深度尺和多用尺指标线棱边至主尺标记面的距离 ········?? (1) 4.2 标尺标记的宽度和宽度差·········································?? (1) 4.3 测量面的表面粗糙度··············································?? (1) 4.4 测量面的平面度 ·················································? ? (2) 4.5 角度样板的偏差和测角尺的示值误差 ································?? (3) 4.6 主尺边缘线性标尺的示值误差 ········，········，···················? ? (3) 4.7 高度尺的零值误差和示值误差 ····································?? (3) 4.8 咬边深度尺的零值误差和示值误差 ································?? (3) 4.9 宽度尺的示值误差 ··············································?? (3) 4.10 间隙尺的示值误差 ······，，····································?? (3) 5 通用技术要求·····················································?? (3) 6 计量器具控制······················································?? (3) 6.1 检定条件 ························································?? (3) 6.2 检定项目······················································?? (4) 6.3 检定方法 ·····················································?? (5) 6.4检定结果的处理·······??(7) 6.5 检定周期······················································?? (7) 附录 A 专用样板的技术要求 ·········································?? (8) 附录 B 咬边深度尺示值误差的测量结果不确定度评定 ··················?? (9) 附录 C 测角尺示值误差的测量结果不确定度评定 ························一 (12) 附录 n 检定证书和检定结果通知书内页格式 ··························?? (ia) JJG 704- 2005 附录 A 专用样板的技术要求 A.1 专用样板的技术要求见图 A.1和表 A.lo 表 A.1 L /mm 6, 8,12,24,32,48 H/mm 6 a/(“) ‘60 注:L值的制造偏差不超过t0.05mm，用千分尺测量 L值。 其余3.2/ 图 A.1 专