600MW超临界锅炉高温过热器氧化皮脱落爆管原因分析及对策.docxVIP

  • 13
  • 0
  • 约8.1千字
  • 约 3页
  • 2019-10-19 发布于江西
  • 举报

600MW超临界锅炉高温过热器氧化皮脱落爆管原因分析及对策.docx

文章编号:1005-006X(2008)04-0032-03600 MW 超临界锅炉高温过热器氧化皮脱落爆管原因分析及对策伟 1李友庆 2 熊蔚立 1 王双勇 2 冯斌 1何军民 1黄(1.湖南省电力公司试验研究院,2.大唐湘潭发电有限责任公司)摘 要:大唐湘潭发电有限责任公司 4 号超临界锅炉运行不到 4000 h 就发生高温过热器管氧化皮层脱落堵塞而引起短期过热爆管。需 文章编号:1005-006X(2008)04-0032-03 600 MW 超临界锅炉高温过热器氧化皮脱落爆管原因分析及对策 伟 1 李友庆 2 熊蔚立 1 王双勇 2 冯 斌 1 何军民 1 黄 (1.湖南省电力公司试验研究院,2.大唐湘潭发电有限责任公司) 摘 要:大唐湘潭发电有限责任公司 4 号超临界锅炉运行不到 4000 h 就发生高温过热器管氧化皮层脱落堵塞而引起短期过热爆管。需 要指出的是,全国在运的超临界锅炉也多次发生由于氧化皮层脱落造成锅炉受热面堵塞而爆管。为此,从机理上分析了 SA-213TP3476H 材质氧化皮生成、脱落、聚积原因,指出由于该材质晶粒度等级低,造成其氧化皮脱落并堵塞管子而引起爆管,并从运行的角度提出和 实施了防止高温过热器氧化皮脱落的技术措施。运行和定期检查表明,3、4 号锅炉高温过热器氧化皮产生、脱落和聚积得到有效控制, 取得明显的效果。 关键词:超临界锅炉;高温过热器;爆管;氧化皮;措施 中图分类号:TK227.1 文献标识码:A Invalidation Analysis Of Final Stage Super Heater On Super Critical Boiler HUANG Wei, LI You-qing, XIONG Wei-li, et al. Abstract: There occurred burst because of oxide skin broken off at the final stage super heater during its 4000 hours operation on Hunan Xiangtan Power Generation Co., Ltd. It was pointed out that occurred domestic time after time. So it was analyzed on mechanism how the scale of SA-213TP3476H came into being, broke off and assembled. Because of low grade of grain size of that material, pipe was jammed and then broke due to scale broken off. The technical treatment was brought up to prevent the scale broken off from final stage super heater, and such bursts never happened again up to now. Key words: super critical boiler; final stage super-heater; pipe break; scale; treatment 2007 年 6 月 30 日,大唐湘潭发电有限责任公司(以下 简称“湘潭电厂”)4 号超临界锅炉运行不到 4 000 h,即发 生高温过热器爆管,其主要原因为高温过热器管内壁的氧化 皮层脱落,聚积在 U 型弯底部,减小了管道的通流截面, 增加了蒸汽的流通阻力,管子内蒸汽流量相对减小,严重减 弱了对管子的冷却效果,造成了高温过热器管短期过热爆 管。需要指出的是全国在运的超临界锅炉多次发生由于氧化 皮层脱落造成锅炉受热面堵塞而短期过热爆管,因此有必要 采取相应的技术措施,防止高温过热器氧化皮脱落。 面管子的材质均为国产 SA213-TP347H。管屏内外圈管采用 不同的管子规格,外圈管为Φ50.8×8.9 mm,其余的为Φ45 ×7.8 mm,顶棚以上材料为 T91,顶棚以下为 TP347H。 表 1 高温过热器管子节流孔径(mm) 序 号 1 2 3 4 5 6 7 8 9 10 节流孔径 32.8 15.0 15.0 15.0 15.0 15.0 14.5 14.5 14.5 14.0 序 号 11 12 13 14 15 16 17 18 19 20 节流孔径 14.0 14.0 14.0 13.5 13.5 13.5 13.0

文档评论(0)

1亿VIP精品文档

相关文档