电机的拆卸和装配流程.pptVIP

2021/2/11 * a、所有拆解下来的螺栓、圆螺母、垫片、密封件等小件 零件,必须按照一定的分类,使用合适的容器,妥善存放。 keep nuts, screws, spacers, seals in box. b、拆解完的设备,应使用合适的工具清理废油脂、密封 胶、异物等污物。 cleaning surface. 2021/2/11 * 5、本章小节 Summarize 2021/2/11 * a、电机的平衡检查 Mark 电机的转子平衡对电机的使用至关重要,一般电动机出厂前都经过动静平衡试验,所以在我们日常 检修中,只需对电机轴用百分表进行跳动检查,即可大概地确定电机的装配平衡性。 The balance of the rotor is essential to the?use of motor, General?Motors?factory have been?static and dynamic balance test,?so?in our daily maintenance,? just?on the motor shaft?with the dial gauge?forrunout check,? can?roughly?determine the assembly?balancingmachine. 2021/2/11 * 谢谢! Thank you! 2021/2/11 * 三相异步电机的拆装维护 2021/2/11 * （三）电机的拆解 Motor’s dismantling 2021/2/11 * 1、准备工作 Ready 2021/2/11 * a、确认说明书 check manual b、工具的准备 prepare tools 设备铭牌、型号、零件清单、标准件规格、 组装图、维护注意事项 nameplate, model, parts list, stand parts, assembly drawing, attention 内六角扳手、棘轮扳手、呆扳手、延长杆、套筒、铁/胶锤、撬棍等 hex wrench, ratchet wrench, solid wrench, extension rod, sleeve wrench, hammer, crowbar, etc. 注意:工具准备应以常用工具为主,取用方便的其他工具,用时取出即可! Attention:ready common tools 注意:从组装图可以分析出这台设备正确的拆解顺序. Attention: Know correct sequence by reading assembly drawing. 2021/2/11 * c、辅助器材准备 d、劳保用品的准备 工作台、吸油纸及垃圾桶、木方、塑料盒 workbench, crane, oil-absorbing sheet, trashcan, wood, plastic box 工作服/围裙、防滑手套、薄手套、安全鞋 labour suit, slip-proof glove, mitten, safety shoe 2021/2/11 * e、切断能量源 f、设备清洁 关停管道阀门 关停电力 关停压缩空气等 close pipeline valve power off compressed air off 注意:正确执行LOTO程序! Attetion:Execute LOTO exactly 去除设备表面污物,油污、灰尘等 clean sewage, oil, dust on the equipment surface 2021/2/11 * 2、执行拆解 Dismantling 2021/2/11 * a、拆除前标记位置 Marking before dismantling b、电源线拆除 Remove cable 标记接线盒盖 → 标记电机风扇罩 → 标记前端盖 mark cable cap → mark fan cap → mark front end 拆除接线盒盖板→并确认接线图 remove cable → check wiring 2021/2/11 * c、拆解后端 dismantle back end 电机风扇的拆除,应使用两爪拉马拉出。 should using puller with two claws to remove plastic fan. 拆除电机护罩 → 标记后端盖位置 → remove fan cap → mark back end →拆除散热风扇 →松后端螺栓 → remove fan → loose back screw 2021/2/11 * d、拆