英培训3分析和总结.docxVIP

TRANSLATING NAME: REMARK: THE ATTACHED IS FINISHED GERBER FILE AND SOLDER-PASTE FILE ABOUT P/N: *******, P/O: *******, PLS SEE IT. 附件是P/N: *******, P/O: *******完成后的 GERBER 文件和贴片文件，请查看 QUESTION: YOU REQUEST DO NOT ADD MANUFACTURER LOGO ,ADD UL，94V-0DATE CODE ,BUT WE REGISTERED OUR LOGO AND REGO NUMBER FROM UNDERWRITERS LABORATORY ,THE UL MARK MUST INCLUDE :FP LOGO,UL,94V-0...,SO PLEASE CONFIRM WE SHOULD ONLY ADD DATE CODE OR ADD THE FULL UL MARK(INCLUDING MANUFACTURER LOGO ),AT THE SAME TIME ,THE ROOM FOR UL MARK IS TOO SMALL. SUGGESTION: ONLY ADD DATE CODE(WWYY) 问题：你们要求不加厂商标记，加UL 标记，防火等级和周期，但是我们从UL 保险公司 注册标记时，UL 标记必须包含快捷标记，UL，防火等级等，所以请确认我们是仅加周期， 还是加整个UL 标记（包括厂商标记），同时，板内空间太小，加不下整个UL 标记。 建议：仅加周期（WWYY） QUESTION: YOU REQUEST BOARD WARPAGE SHALL NOT EXCEED 0.254 SQR MM,WHAT ON EARTH THE WARPAGE IS? SUGGESTION: NOT EXCEED 1% 问题：你们要求翘曲度不超过0.254 平方毫米，这翘曲度到底是多少建议：翘曲度不超过1% QUESTION: AS THE PICTURE BELOW (1.JPG),THE HOLE SIZE AT THE SAME DEVICE IS DIFFERENT SUGGESTION: 1.FOLLOW THE DRILL FILE 2.ENLARGE THE SMALL HOLE TO MAKE THE SAME HOLE SIZE 问题：如图 1 同一器件孔径不一样大建议：1.按钻带 2.加大小孔做同一孔径 QUESTION 1.THE PROFILE OF THE UNITS IS SIMILAR TO SIME-CIRCLE,BUT IN THE STORMLITEL_PANEL DRAWING,THE OUTLINE OF THE 5 UNITS IS CIRCLE, THEN HOW CAN I MAKE SEMICIRCULAR OUTLINE PANELIZE TO CIRCULAR ONE(ONLY 5 UNITS IN PANEL) . SO PLEASE CONFIRM ATTACHMENT THE GERBER FILES AND PANEL OUTLINE DIMENSION! SUGGESTION: FOLLOW ATTACHMENT THE GERBER FILES AND PANEL OUTLINE DIMENSION 问题：单元板外形类似半圆，但是在拼版图STORMLITEL_PANEL DRAWING 中，5 个单元板外形是圆形，仅 5 个单元板拼在一起，我们怎么把半圆形做成圆形，所以请确认附件中的拼版和外形 建议；按附件中的拼版和外形尺寸 QUESTION 1.AS FOLLOW PICTURE,HOLE TOLERANCE TOO CLOSE,WE COMPANY NOT EASY CONTROL,PLS CONFIRM SUGGESTION: ACCORDING TO OUR COMPANY GENERAL (ALL HOLES TOLERANCE :+/-0.075MM) 问题：如图，孔径公差太严，我们公司不能够控制，请确认建议：按我们公司能力所有孔径公差按+/-0.075MM AS THE PICTURE BELOW (1.JPG), THE BOTTOM OVERLAY CONTAINS THE UL LOGO AND DATE CODE, REPLACE THE MARKING OF MY COMPANY (FP LOGO,UL,94V-0...)? 问题：如图 1，底层字符 本身包含UL 标记和周期，是否替换成我们公司标记（快捷标记，UL，防