业英语图解教程（第2版）-侯锁军课件 unit8-unit13.pptVIP

Unit 8 FUEL SUPPLY SYSTEM FOR DIESEL ENGINE 图8.1 Fuel supply system for diesel engine柴油机燃料供给系的组成 1.oil tank柴油箱; 2.low pressure pipe低压油管;3.oil fiter柴油滤清器;4.feed pump输油泵; 5.injection pump喷油泵;6. return pipe回油管;7.hign pressure pipe高压油管;8. combustion chamber燃烧室;9.exhaust pipe排气管;10.injector喷油器;12. induction pipe?进气管;13.air filter空气滤清器 图8.2 Hole type injector孔式喷油器 a）nozzle喷油嘴 b）injctor喷油器 1. fuel return pipe screw回油管螺钉；2.fuel return gasket 回油管垫片；3. pressure-regulator screw cap调压螺钉护帽；4.gasket垫片；5.eject rod顶杆 ；6.injctor housing喷油器体；7. fastening screw cap紧固螺套；8.dowel定位销；9.nozzle gasket油嘴垫；10.injection hole喷孔；11.pintle valve针阀；12.ring body环形油腔；13. pintle valve housing针阀体；14.fuel inlet gallery进油道；15. fuel inlet joint进油管接头； 16pressure－regulator spring.调压弹簧；17. pressure-regulator screw调压螺钉 图8.3 Nozzle injector轴针式喷油器 1. return oil pipe screw 回油管螺钉；2. pressure-regulator screw cap调压螺钉护帽； 3.pressure-regulator screw调压螺钉； 4.washer垫圈； 5.filter core滤芯；6.oil inlet joint进油管接头； 7.fastening screw cap紧固螺套 ； 8.pintle vavle针阀； 9.washer垫圈； 10.pintle valve housing针阀体； 11.injectior body喷油器体；12.eject rod顶杆；13.washer垫圈； 14. pressure－regulator spring调压弹簧； 15.washer垫圈 ； 16.washer垫圈 图8.4 Pump for injection pump喷油泵的泵油 1.delivery valve holder出油阀压紧座；2.delivery valve spring出油阀弹簧；3.delivery valve出油阀 4.delivery valve seat出油阀座；5.plunger collar柱塞套；6.low pressure fuel body 低压油腔；7.plunger柱塞； 8.injection pump housing喷油泵体；9.fuel adjusting screw油量调节螺杆； 10.fuel adjusting sleeve油量调节套筒；11. plunger spring柱塞弹簧; 12. ?fuel supply timing ?adjusting screw供油正时调节螺钉; 13. positioning slide定位滑块 14. ??camshaft凸轮轴 15.cam凸轮 16.cylinder components挺柱体部件；17.plunger spring underseat柱塞弹簧下座；18. plunger spring overseat柱塞弹簧上座；19.ring gear齿圈；20.into oil return hole进回油孔；21.seal washer密封垫 图8.5 Fork (connecting rod) fuel adjusting structure拨叉拉杆式油量调节机构 1. plunger collar柱塞套; 2. plunger柱塞;3. plunger adjusting arm柱塞调节臂;4.fork fastening screw拨叉紧固螺钉;5.fork拨叉; 6.fuel-supplyconnecting rod供油拉杆 图8.6 Piston feed pump活塞式输油泵 1.fu