模具表面处理课件.pptxVIP

抛光（Polish)砂（Blasting）

SPI-SocietyofthePlasticsIndustry塑料工业协会

DescriptionandPreviousFinishNumbersPaperStoneisslightlyfinerthaniscomparabletoisslightlyfinerthaniscomparabletoDryBlastedisalittlemorecoarsethan

石抛砂抛光光（非高光面，良好脱模，也是砂和石抛光的道工序）（微高光面，良好脱模，用在装要求不高的合）（非常适合（网点和理表面）SPIA-1（高量外片模具）SPIA-2SPIA-3

火花纹(ThinFireTexture)

号码01234567891011121314151617181920

号码咬花深度0.01020.02540.03810.05080.07620.11430.07620.07620.05080.08890.15240.06350.05080.06350.06350.06980.1016MT-11000MT-11010MT-11020MT-11030MT-11040MT-11050MT-11060MT-11070MT-11080MT-11090MT-11100MT-11110MT-11120MT-11130MT-11140MT-11150MT-11160

蚀纹处理和模具斜度的关系Ptn.#MT-11000MT-11010MT-11020MT-11030MT-11040MT-11050MT-11060MT-11070MT-11080MT-11090MT-11100MT-11110MT-11120MT-11130MT-11140MT-11150MT-11160Depth(mm)0.00040.0010.00250.00350.00450.0050.00450.00250.0040.00150.0020.00250.0020.0040.0050.0040.00350.0055

蚀纹处理和模具斜度的关系Depth0.0020.00250.00350.0020.00250.00350.0070.0100.00050.00150.00250.0030.00350.0050.0020.0020.003

MT1013MT1015MT1039MT1055MT1068MT1070MT1074MT1129MT1159MT1122MT1125MT1126MT1127MT1526

1°1.5°2°2°3°4°4°4.5°1.5°2°2.5°3°

S---半光泽

S---半光澤

S---半光澤

封封

咬花番号HN1000HN1001HN1002HN1003HN1004HN1005HN1006HN1007HN1008HN1009HN1010HN1011HN1012HN1013HN1014HN1015HN1016HN1017拔模斜度1°1°打光程度#800#8001.5°1°1°1°2°2.5°3°1.5°2°3°3.5°4°5°3°4°5°

打光程度#600#600#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400#400HN2000HN2001HN2002HN2003HN2004HN2005HN2006HN2007HN2008HN2009HN2010HN2011HN2012HN2013HN2014HN2015HN2016HN2017HN2018HN2019HN2020HN2021HN2022HN2023HN2024HN2025HN20261.5°2°13~1522~3440~4444~4761~6560~6361~6463~6633~3543~4620~2128~3230~3519~2225~2933~3838~4150~5870~7516~2323~2625~2730~3442~5052~5662~702.5°3.5°4°5.5°5.5°5°5°3°3.5°2°3°3.5°2.5°2.5°3°4°4°5°2°2.5°3°4°4.5°5°5°

打光程度#8003°

二次封砂用封除去

中等耐磨修正公差要求不高的位置（0.003”）

Asplated450/50RCHeattreatedat:-4hr,350°F(177°C)480to520-1hr,750°F(400°C)Phosphoruscontent,wt,%:Meltingpoint:ASTMB-1171.0mildeposit,