网卡驱动加载.docVIP

改变网口顺序 将/etc/sysconfig/network-scripts中eth0的mac地址改为对应第一个口的mac，逐一修改 CODE: #tar zxf e1000-x.x.x.tar.gz#cd e1000-x.x.x/src/#make install#insmod e1000#reboot#vi /etc/sysconfig/network-scripts/ifcfg-eth0DEVICE=eth0　　　　　　　　 #设定网卡的名称，要跟文件名称对应 #ONBOOT=yes　　　　　　　　 #是否在开机的的时候启动网卡#BOOTPROTO=static　　　　　 #如果是动态主机的话，要改成 dhcp 才行#IPADDR=192.168.0.1　　　　 #IP 地址#NETMASK=255.255.255.0　　　 #子网掩吗#NETWORK=192.168.0.1　　　　 #该网段的第一个 IP#BROADCAST=192.168.0.255　　 #最后一个同网段的广播地址#GATEWAY=192.168.0.1　　　　 #网关地址# 　　　　:x存盘后使用命令激活 CODE: #service network restart [root@test boot]# ethtool -i eth0 driver: e1000e version: 1.0.2-k2 firmware-version: 5.0-6 bus-info: 0000:0a:00.0 [root@test ~]# cd /boot [root@test boot]# ls config-2.6.31.5-127.fc12.i686.PAE lost+found efi System.map-2.6.31.5-127.fc12.i686.PAE grub vmlinuz-2.6.31.5-127.fc12.i686.PAE initramfs-2.6.31.5-127.fc12.i686.PAE.img [root@test boot]# [root@test boot]# [root@test boot]# [root@test boot]# cat config-2.6.31.5-127.fc12.i686.PAE | grep 4 # CONFIG_64BIT is not set # CONFIG_X86_64 is not set # CONFIG_M486 is not set # CONFIG_MPENTIUM4 is not set CONFIG_X86_L1_CACHE_BYTES=64 CONFIG_X86_INTERNODE_CACHE_BYTES=64 CONFIG_X86_CMPXCHG64=y CONFIG_X86_MINIMUM_CPU_FAMILY=4 # CONFIG_HIGHMEM4G is not set CONFIG_HIGHMEM64G=y CONFIG_ARCH_PHYS_ADDR_T_64BIT=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_PHYS_ADDR_T_64BIT=y CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_X86_RESERVE_LOW_64K=y CONFIG_PHYSICAL_START=0x400000 CONFIG_PHYSICAL_ALIGN=0x400000 CONFIG_X86_P4_CLOCKMOD=m CONFIG_NF_DEFRAG_IPV4=y CONFIG_NF_CONNTRACK_IPV4=y CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_ATM_BR2684=m # CONFIG_ATM_BR2684_IPFILTER is not set CONFIG_IEEE802154=m CONFIG_NET_CLS_ROUTE4=m CONFIG_BT_HCIUART_H4=y CONFIG_MTD_MAP_BANK_WIDTH_4=y # CONFIG_MTD_CFI_I4 is not set CONFIG_MTD_CK804XROM=m # CONFIG_MTD_L440GX is not set CONFIG_MTDRAM_TOTAL_SIZE=4096 CONFIG_MTD_UBI_WL_THRESHOLD=4096 CONFIG_PARPORT_1284=