TONTimer開關1ON0OFFPR1.ppt

Timer TON: Timer 開關 1:ON 0:OFF PR1: Timer計數值設定 TSIDL: 休眠模式 1:休眠 0:不休眠 TMR1: Timer內計數值 TGATE: 閘控模式選擇 TSYNC: 選擇16位元同步或非同步計數器 TCS: 選擇計數源 0:內頻 1:外頻 TCKKSP: 除頻 00 = 1:1 prescale value 01 = 1:8 prescale value 10 = 1:64 prescale value 11 = 1:256 prescale value timer1 /* timer計數 */ #include p30F4011.h //呼叫p30F4011(IC)指令巨集 #include timer.h unsigned int i=0; unsigned int x=0x20,y=0; _FWDT(WDT_OFF); //關閉看門狗 void Init_Timer1( void ) { T1CON = 0; //TIMER1 OFF IFS0bits.T1IF = 0; //中斷旗標 IPC0bits.T1IP = 7; //中斷優先權設定 IEC0bits.T1IE = 1; //中斷觸發暫存器 T1CONbits.TCS = 0; T1CONbits.TCKPS=1; //TCKPS1:0: Timer Input Clock Prescale Select bits //11 = 1:256 prescale value //10 = 1:64 prescale value //01 = 1:8 prescale value //00 = 1:1 prescale value PR1 = 1250; // ((10MHz*8[選擇的8倍頻])/4[內部除頻])/8/1250=2KHz 中斷為0.5ms T1CONbits.TON=1; //TIMER1 ON } /* timer中斷副程式 */ void _ISR _T1Interrupt(void) { if(i==2000) //0.5ms*2000=1s { PORTB =0x1c+x; x+=0x20; if(x0x130) x=0x00; i=0; } else i++; IFS0bits.T1IF = 0 ; //清除中斷旗標 } /* 主程式 */ int main(void) { TRISB = 0x0000 ; // 0B 0000 0000 0000 0000 PORTB=0x1c; // 1=input // 0=output Init_Timer1(); while(1); } timer2 /* timer2 */ #include p30F4011.h //呼叫p30F4011(IC)指令巨集 #include timer.h int IntCount=0; _FWDT(WDT_OFF); //關閉看門狗 void Init_Timer2( void ) { T2CON = 0; //TIMER2 OFF IFS0bits.T2IF = 0; //中斷旗標 IPC1bits.T2IP = 7; //中斷優先權設定 IEC0bits.T2IE = 1; //中斷觸發暫存器 T2CONbits.TCS = 0; T2CONbits.TCKPS=1; //TCKPS1:0: Timer Input Clock Prescale Select bits //11 = 1:256 prescale value //10 = 1:64 prescale value //01 = 1:8 prescale value //00 = 1:1 prescale value PR2 = 1250; // ((10MHz*8[選擇的8倍頻])/4[內部除頻])/8/1250=2KHz 中斷為0.5ms T2CONbits.TON=1; // TIMER2 ON } /*timer2 中斷 */ void _ISR _T2