- 1、本文档共7页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
C公司财务报表分析分两套doc
C10022公司财务报表分析
第一套 100分
第二套 100分
Ellipticity of elbow pipes with diameters less than or equal to 150 mm must be not greater than 8% diameter of 200 mm or less shall not be greater than 6%. Wall thickness of the pipe wall thinning rate must not exceed the original 15%. Crease roughness: diameter 125 mm or less, shall not exceed 3 mm diameter less than or equal to 200 mm, not more than 4 mm. 7.3.9 simmering bending production of square steel tube extension, to use the whole tube bending. Interface if necessary, the welding position should be located in the middle of the vertical arm. 7.3.10 install expansion joints should be done. If design is not required, pipe compensator lengthen should conform to the requirements in the following table: square scale length δ x is equal to 1/2. Pre stretch tolerance: casing + 5 mm, +10 mm. 7.3.11 pipe form, location, spacing shall meet the design and specifications. 7.3.12 piping on back or return pipe at higher levels of the upper to automatic valve to install a drain valve below the horizontal parts. 7.3.13 supports and hangers of checks and the number 1) hanger installed must be checked before installation of supports and hangers part models, specifications of springs setting values, whether the materials meet the requirements of drawings and documents; 2) supports and hangers of material, size and accuracy shall conform to the provisions of the design drawings, material technical requirements should be consistent with national standards, industry standards and technical requirements related to the alloy spectrum review should be carried out; 3) pipe supports and hangers part plant product quality certificate for each variable spring supports, constant support hangers, dampers, damper function, there should be factory calibrated test
Ellipticity of elbow pipes with diameters less than or equal to 150 mm must be not greater than 8% diameter of 200 mm or less shall not be greater than 6%. Wall thickness of the pipe wall thinning r
您可能关注的文档
- 4T锅炉产品说明书doc.doc
- 11毕业论文写作要求doc.doc
- 5经济法概论答案doc.doc
- !胡柏玲讲座稿doc.doc
- 6机械注塑料模具毕业课程设计说明书论文参考资料doc.doc
- 7机械注塑料模具毕业课程设计说明书论文参考资料doc.doc
- adsl 使用说明书doc.doc
- AFP和CFP和ICFP介绍说明doc.doc
- AiTOP 设计速写讲座视频学习笔记doc.docx
- Anbound行业竞争情报及分析doc.doc
- 江苏省灌云高级中学2023-2024学年高三上学期第一次月考地理试题含答案.docx
- 备战2024年高考物理一轮重难点复习 第十三章 近代物理.docx
- 江苏省高邮市一中2021-2022学年高三上学期第一次月考语文试题(原卷版).docx
- 江苏省华罗庚中学2023-2024学年高三上学期12月阶段检测数学试卷含答案.docx
- 江苏省海门中学2023-2024学年高三上学期第一次调研考试地理试题及答案.docx
- 备战2024年高考物理一轮重难点复习 第九章 恒定电流.docx
- 江苏省高邮市2023-2024学年高三下学期3月学情调研数学试题含答案.docx
- 备战2024年高考物理一轮重难点复习 实验十一:探究影响感应电流方向的因素.docx
- 备战2024年高考物理一轮重难点复习 实验三:验证平行四边形定则.docx
- 备战2024年高考物理一轮重难点复习 第十四章 光.docx
文档评论(0)