注塑工艺参数及调整（Injection molding process parameters and adjustment）.docVIP

下载本文档

20
0
约1.05万字
约 10页
2017-07-27 发布于河南
举报
版权申诉

注塑工艺参数及调整（Injection molding process parameters and adjustment）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

注塑工艺参数及调整（Injection molding process parameters and adjustment）

注塑工艺参数及调整（Injection molding process parameters and adjustment） This article is contributed by ZHOUNING8899 DOC documents may experience poor browsing on the WAP side. It is recommended that you first select TXT, or download the source file to the local view. First, the injection process can be expressed as follows: The end of the last cycle - die closing - filling - holding - back glue - cooling - mold opening - release - start the next cycle In the insurance period of filling cavity pressure drop, but rise over time, then fill the cavity pressure will remain in a relatively static state, to the shrinkage amount of glue, in addition to this pressure can To prevent backflow phenomenon caused by injection of colloid decreases, which is the holding stage, after finished packing the cavity pressure gradually decreased, and over time can theoretically be reduced to zero, but the actual is not zero, so off After the mold, the internal memory of the product is internally stressed, so some products need to be treated to eliminate the residual stress. The so-called stress is the chain or chain segments to Fu Taka. Freedom of movement, the bending deformation, stress cracking, shrinkage Etc.. Two, the main parameters of the injection molding process 1, plastic injection temperature, melt temperature on the melt flow properties play a major role, because there is no specific plastic melting point, melting temperature is called a molten state, not plastic molecular chain structure and composition At the same time, so the liquidity effect is also different, rigid molecular chain is affected by temperature is obvious, such as PC, PPS, and flexible molecular chains such as PA, PP, PE and other liquidity by changing the temperature is not obvious, so we should be According to different materials to adjust the reasonable injection temperature. 2, the injection speed is melt inside the barrel (also speed screw) speed (MM/S) injection speed decide the product appearance, size, shrinka