典型零件热处理实例（Example of heat treatment of typical parts）.docVIP

下载本文档

23
0
约2.09万字
约 22页
2017-07-27 发布于河南
举报
版权申诉

典型零件热处理实例（Example of heat treatment of typical parts）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

典型零件热处理实例（Example of heat treatment of typical parts）

典型零件热处理实例（Example of heat treatment of typical parts） Examples of heat treatment of typical parts, examples of shaft heat treatment Example of shaft heat treatment I. working conditions, materials and heat treatment requirements 1. conditions: Work in the sliding bearing, by week less than 2m/S requirements has high surface hardness on the small shaft, spindle. Such as machine tool feed box, transmission shaft. Requirements: 45, 50, complex shape of shaft with 40Cr, 42MnVB. quenched and tempered, HB228-255, axis High frequency quenching at neck, HRC45-50 2. conditions: working in the sliding bearing, The week is less than 3m/S, require high rigidity, small deformation, such as the small shaft intermediate belt drive Requirements: 40Cr, 42MnVB quenching and tempering, HB228-255, high frequency quenching of shaft neck, HRC45-50. 3. conditions: V week is more than 2m/S, small shaft bending load and friction under the conditions, such as small shaft gear box machine. Requirements: 15, 20, 20Cr, 20MnVB carburizing, quenching, low temperature tempering, HRC58-62. 4. conditions: high load spline shaft, requiring high strength and wear resistance, small deformation Requirements: 45 high frequency heating, water cooling, low temperature tempering, HRC52-58. 5. conditions: rolling or sliding bearings in the work, light or medium load, low speed, low precision requirements, With slight impact, the fatigue load can be omitted by the spindle or in the rolling bearings, light load, Secondary V 1m/s spline shaft. Requirements: 45, quenching and tempering, HB225-255 (such as general simple machine spindle) 6. conditions: work in rolling or sliding bearings, light or medium load, slightly higher speed P v = 150N.m/ (cm^2.s), high precision, shock, fatigue load is small. Requirements: 45 normalizing or tempering, HB228-255, shaft neck or assembly surface quenching, HRC45-50. 7. conditions: working in the sliding bearing, in high speed or heavy load, p v = 400N.m/cm^2.S, Higher preci