技术要求需要写的那些东西（Technical requirements need to write those things）.doc

下载文档 降价啦

2
0
约9.8千字
约 9页
2017-08-17 发布于河南
举报
版权申诉
保障服务

技术要求需要写的那些东西（Technical requirements need to write those things）.doc

1、本文档共9页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

技术要求需要写的那些东西（Technical requirements need to write those things）

技术要求需要写的那些东西（Technical requirements need to write those things） 1. parts remove oxide skin. 2. parts processing surface should not have scratches, scratches and other parts of the damaged surface defects. 3. deburring edges. 4. by quenching and tempering treatment, HRC50 ~ 55. 5. parts are subjected to high frequency quenching, tempering at 350~370 DEG C, HRC40 ~ 45. 6. carburizing depth 0.3mm. 7. high temperature aging treatment. 8. no injection form tolerances shall comply with the requirements of GB1184-80. 9. no injection length dimension allowable deviation + 0.5mm. 10. the tolerance zone of casting is symmetrical to the basic dimension of rough casting. 11. no fillet radius R5. 12. no injection chamfer is 2 x 45 degrees. 13. acute angle blunt. 14. the seals must be soaked before they are assembled. 15. rolling bearings are allowed to be heated by oil heating. The temperature of the oil shall not exceed 100 degrees. 20. after the gear assembly, the tooth surface contact spot and the backlash should conform to the GB10095 and GB11365 stipulation. 21. sealing filler or sealant shall be allowed for assembly of hydraulic systems but shall be prevented from entering the system. 22. assembly parts and components (including purchased parts, outsourcing parts) must have the certificate of inspection department before they can be assembled. 23. parts must be cleaned and cleaned before assembly. There shall be no burrs, edges, skins, rust, chips, oil stains, stains and dust. 24. before assembly, the main Coordination dimensions of the parts, especially the interference fit size and the relative accuracy shall be reviewed. 25. assembly process, parts are not allowed to knock, touch, scratch and rust. 26. when screws, bolts and nuts are fastened, it is strictly forbidden to strike or use improper screwdrivers and wrenches. The fastening screws, slots, nuts and screws, and the head of the bolt shall not be damaged. 27. tightening torque required fasteners must use torque wr