钢筋工程技术交底（Reinforcement engineering technical disclosure）.docVIP

下载本文档

0
0
约1.17万字
约 11页
2017-08-18 发布于河南
举报
版权申诉

钢筋工程技术交底（Reinforcement engineering technical disclosure）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

钢筋工程技术交底（Reinforcement engineering technical disclosure）

钢筋工程技术交底（Reinforcement engineering technical disclosure） This project reinforcement quantity is big, the steel bar specification is quite many. In order to facilitate the construction, all steel bars are processed and fabricated at the construction site to ensure the timely supply of steel and to ensure the smooth progress of the project. Two. Material preparation 1. Reinforcement: all incoming reinforcement must have a pass to enter the field. The reinforcement shall not be used unless it has been inspected. Material group shall supply materials according to material supply plan in time, and steel bars shall be listed and piled up after entering steel. Check the specification, size and quantity of semi-finished steel bars. Do they conform to the bill?. 2, cushion block: according to the thickness of each part of the protective layer, choose cement mortar block or plastic pad (card) block. 3, lashing wire: choose 20~22 galvanized wire. Three, steel forming process Steel processing shall be according to the construction sequence: beam, pile cap, reinforced basement floor, reinforced basement wall columns reinforced, basement slab reinforced wall column reinforced, conversion layer to two layer slab reinforced wall column reinforced layer, standard, standard layer beam plate and roof beam board, roof frame reinforced steel bars. And parts, specifications listed neatly stacked classification. Four, steel processing 1. Bending and bending of stressed steel bars shall comply with the following provisions: The end of a and grade I steel bars shall be bent at 180 degrees. The diameter of the bent arc shall not be less than 2.5 times of the diameter of the steel bar, and the length of the curved part of the bent hook shall not be less than 3 times of the diameter of the steel bar. B, when the design requirements, the end of the steel bar for 135 degrees bending hook, HRB335 and HRB440 grade steel bending arc diameter should not be less than 4 times the diameter of the steel