发电机转子绝缘不合格的简单处理方法（Simple handling method of generator rotor insulation failure）.docVIP

下载本文档

1
0
约7.03千字
约 6页
2017-09-07 发布于河南
举报
版权申诉

发电机转子绝缘不合格的简单处理方法（Simple handling method of generator rotor insulation failure）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

发电机转子绝缘不合格的简单处理方法（Simple handling method of generator rotor insulation failure）

发电机转子绝缘不合格的简单处理方法（Simple handling method of generator rotor insulation failure） Processing method for substandard insulation of generator rotor [Abstract] this paper mainly introduces the air-cooled generator rotor insulation for analysis and treatment method of zero reason, mainly introduces the generator rotor non metallic grounding of the simple and fast processing method. This method can not pump rotor, also dont pull the retaining ring, and for a short time, low cost, high economic benefit. The 1 main causes of the decrease of insulation of generator rotor 1.1 rotor due to damp caused by insulation resistance is reduced to allowable value, such as the generator outage time is long, wet environment caused by insulation resistance decreased. 1.2 rotor because life is longer, or running for a variety of reasons make the rotor overheating caused by material aging and deterioration of insulation coil. A carbon powder or oil accumulation under the 1.3 ring, the rotor lead wire insulation damage. 1.4 because of the cooling system of generator sealing oil due to the bearing or the rotor coil end product ash, oil or toner, resulting in lower insulation properties. This effect causes by the centrifugal force of the rotor is larger. 1.5 due to the effect of ventilation and thermal expansion in the operation of the rotor at the notch groove lining protection layer aging, fracture or even fall off, the notch groove of mica flakes gradually broken, blown away by the wind and dust caused by factors such as notch. 1.6 insulation fracture groove of the rotor caused by the rotor insulation resistance is too low or metallic grounding. 2 inspection method of rotor insulation 2.1 after stopping inspection methods: shaking table test of rotor insulation on the ground with 1000 volts, when the insulation resistance should be less than 2M ohm for processing. Check the operation of the 2.2 methods: The generator rotor insulation monitoring device through online measurement in operation