变频器igbt模块检测方法（Frequency converter, IGBT module, detection method）.docVIP

下载本文档

4
0
约9.14千字
约 8页
2017-09-08 发布于河南
举报
版权申诉

变频器igbt模块检测方法（Frequency converter, IGBT module, detection method）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

变频器igbt模块检测方法（Frequency converter, IGBT module, detection method）

变频器igbt模块检测方法（Frequency converter, IGBT module, detection method） Frequency converter IGBT module inspection method 26951552006-01-10 09:35:09 A simple method for detecting the quality of insulated gate bipolar transistors (IGBT) 1, determine polarity The multimeter dial in R * 1K block, measured with a multimeter, if a pole and the other two poles of infinite resistance, change the pole and the other two pens after the resistance is infinite, then the very gate (G). The rest of the poles then multimeter, if the measured resistance is infinite, the resistance change after one smaller measurement. In a small resistance measurement, then determine the red pen is connected for the collector (C); the black probe connected to the emitter (E). 2, judge good or bad The multimeter dial in R * 10K block, IGBT connected with the black pen collector (C), red emission probe connected to the IGBT pole (E), the meter pointer to zero. With fingers touching the grid (G) and the collector (C), the IGBT is triggered and the pointer of the meter is placed in a smaller resistance direction and can be stopped indicating that it is in a certain position. Then hit the grid (G) and the emitter (E) again with your fingers, when the IGBT is blocked and the pointer of the multimeter goes back to zero. At this point you can judge that IGBT is good. 3, any pointer type multimeter can be used to detect IGBT. Note that when judging IGBT good or bad, you must dial the multimeter in R * 10K Omega block, because R * 1K ohm block following files, multimeter, the internal battery voltage is too low, good and bad when testing can not make IGBT conduction, and can not judge the quality of IGBT. This method can also be used to check the performance of power field effect transistors (P-MOSFET). Capacitance The identification method is basically the same as that of resistance identification. There are 3 kinds of methods: direct calibration, color coding and digital calibration. The basic unit of capacitanc