linux下的oss音频接口编程一例（Linux audio interface programming under OSS example）.docVIP

下载本文档

20
0
约 11页
2017-10-05 发布于河南
举报
版权申诉

linux下的oss音频接口编程一例（Linux audio interface programming under OSS example）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

linux下的oss音频接口编程一例（Linux audio interface programming under OSS example）

linux下的oss音频接口编程一例（Linux audio interface programming under OSS example） Linux under the OSS audio interface programming, an example of Linux under the OSS audio interface programming example General framework that should be followed when performing audio programming using OSS: (1) turn on the audio device; (2) set the sampling format (i.e., quantization bits); (3) set the number of channels (mono or stereo); (4) set sampling rate (i.e. sampling speed); (5) read data from a device or write data to a device; (6) turn off the audio device; In the above process, (6) is optional because the open file description word is closed when the process is normal or out of order, thus releasing the resources of the audio device. However, in addition to the five step and the other is not the lack of order and cannot be reversed (OSS programming guide this explanation is: set the sampling rate can not work in all of the audio hardware — before the specified number of — if the card is set after the high sampling rate mode changed the number of channels. The application will appear incorrect behavior. At the same time, you must set the sample rate before using read () or write () to call read and write data. This is a small program written by the author to read and write /dev/dsp devices. It can be used to record a sound, and it can also be used to play the sound recorded in a file. In addition, you can specify device parameters through command line parameters, such as sampling rate, quantization number, channel number, sound length to be recorded, and so on. The detailed command line arguments are explained below: SndKit, [-h], [-d, device], [-c, channel], [-b, bits], [-f, hz], [-l, len], lt, -r|-p, file Among them: uml: -h: print help information; uml: -d: Specifies the audio device to read and write (default to /dev/dsp); uml: -c: Specifies the number of channels used (default is MONO, mono); uml: -b: Specifies the quantization bit number (default is 8 bit unsigned integer); uml: -