毕业设计 采矿工程 校级优秀毕业论文.docx

摘要本设计为武山铜矿南矿带日产原矿1000t地下开采方案。根据矿体赋存条件及矿山开采技术条件，地下开采范围为0m～-800m，阶段高度均为50m。通过武山铜矿地质状况调研以及开采要求的综合分析比较，确定了采用下盘竖井开拓方案；采矿方法主要为下向水平分层充填采矿法；采用侧翼对角式抽出通风系统；井下运输为有轨运输。矿山服务年限约为164a。本设计还对井下排水、充填、供电、供风等作了简单的方案设计，初步形成了完整的地下开采系统。关键词：武山铜矿矿；地下开采；下盘竖井开拓；下向水平分层充填采矿法；侧翼对角式通风。关键词：武山铜矿；地下开采；下盘竖井；下向水平分层充填法，侧翼对角式通风系统。ABSTRACTThe design is underground mining program of WuShan Copper Mine south ore. The daily production of raw ore is 1000t. According to the ore current conditions and mining technological conditions, underground mining range are from 0m to -800m level ,the design phase are 50m high. By the comprehensive analysis and comparison of WuShan Copper Mine geology research and exploitation require- ments, the joint development program of the shaft has been confirmed. Mining methods is mainly on the stratification of hydraulic-fill mining method, and adopting Central Angle ventilation system. Underground transportation are electric locomotive rail transport, and the service life is approximately 164 years. Some simple solution designs for the mine drainage system, filling power supply, wind supply are made. The design of a complete system of underground mining for hunanbaohuaCopper Mine has been accomplished.Key words:WuShan Copper Mine; Underground mining; Shaft joint development; on the stratification of hydraulic-fill mining method; Flank Angle ventilation system.目 录第一章总论11.1 矿山概况11.2 设计依据11.3 设计指导思想与原则21.4矿山建设主要方案21.5存在的问题与建议4第二章矿山地质62.1 矿区地理与气候条件62.2 矿区地质构造72.3 矿脉分布、产状及规模92.5 矿区水文地质122.6 矿区工程地质12第三章矿山年产量及服务年限143.1验算设计产量143.2 矿山服务年限的计算153.3 矿山工作制度15第四章矿床开拓164.1 井田划分164.2 岩体移动范围164.3 阶段高度的确定174.4 矿床开拓方法选择174.5 阶段及矿块开采顺序224.6主副井位置确定224.7风井位置确定234.8主溜井位置确定234.9阶段运输平巷位置确定234.10 井筒及阶段运输平巷位置布置234.11 三级储量23第五章矿山井巷工程255.1 矿山基本井巷工程255.2 井筒及阶段运输巷道断面设计255.3 井底车场形式与马头门尺寸的确定365.4井筒及阶段运输平巷施工要求395.5地下硐室39第六章采矿方法(专题部分)426.1 矿床地质及开采地质条件426.2 采矿方法选择436.3 采矿方法设计51第七章矿井运输与提升597.1 矿山运输597.2 列车编组计算617.3 矿井提升657.4 轨道结构与选型73第八章矿井通风758.1矿井通风概述758.3风量计算788.4矿井风量分配的原则和方法818.5矿井通风阻力计算858.6通风设备选型878.5通风制度918