钽电容冲压成型的表面预处理--毕业论文设计.doc

PAGE 毕业设计说明书（论文）中文摘要 本课题主要是采取阳极氧化的办法在钽表面制备一层致密的氧化膜，氧化膜主要成分为Ta2O5。通过改变电压、电解液成分、电解液温度、电解液浓度、搅拌等影响因素，获得多种氧化膜，测试氧化膜性能。电镜分析得出该氧化膜十分致密，色泽鲜艳，电绝缘性优异，显微硬度计测得Ta2O5膜硬度比钽表面提高了30-40%。在此基础上，又做了另一组改善黏膜实验，即通过制备聚乙烯醇薄膜并覆盖于钽之上，测定膜的接触角，同时测定了氧化膜的接触角。 关键词：钽阳极氧化 表面制膜 接触角 毕业设计说明书（论文）外文摘要 Title Surface treatment of Tantalum for capacitor by punching mould Abstract This passage takes the approach of the anodizing the surface of tantalum for a dense layer of oxide film, the major components of the oxide film is Ta2O5. By changing the voltage, electrolyte composition, electrolyte temperature, electrolyte concentration, stirring, and other factors, can achive a variety of oxide film, Electron microscopy analysis of the oxide film shows which is very dense,bright color, excellent electrical insulation, micro-hard measurement shows the oxide film increases hardness more30-40 percent than the surface of tantalum . Besides this, we have done experiment to improve the mucous membrane of another group, that is through the preparation of polyvinyl alcohol film and cover it on the tantalum,measure the contact angle of the film as well as the oxide film. Keywords Tantalum anodizing surface-film contact angle 目 录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc200972800 第一章 绪 论 PAGEREF _Toc200972800 \h 2 HYPERLINK \l _Toc200972801 1.1金属钽的性质 PAGEREF _Toc200972801 \h 2 HYPERLINK \l _Toc200972802 1.1.1物理性质 PAGEREF _Toc200972802 \h 2 HYPERLINK \l _Toc200972803 1.1.2化学性质 PAGEREF _Toc200972803 \h 2 HYPERLINK \l _Toc200972804 1.1.3力学性能 PAGEREF _Toc200972804 \h 2 HYPERLINK \l _Toc200972805 1．2 钽电容器概述 PAGEREF _Toc200972805 \h 3 HYPERLINK \l _Toc200972806 1.2.1钽电容器简介 PAGEREF _Toc200972806 \h 3 HYPERLINK \l _Toc200972807 1.2.2钽电容器在设备中的应用及发展 PAGEREF _Toc200972807 \h 3 HYPERLINK \l _Toc200972808 1.3钽表面强化处理技术 PAGEREF _Toc200972808 \h 5 HYPERLINK \l _Toc200972809 1.3.1吸氧强化 PAGEREF _Toc200972809 \h 5 HYPERLINK \l _Toc200972810 1.3.2吸氮强化 PAGEREF _Toc200972810 \h 6 HYP