危险气体检测系统程序.docVIP

#include reg52.h #define uchar unsigned char #define uint unsigned int /*端口定义*/ #define LCD_data PO //数据口 #define FOSC_110592M sbit ledO=PlAO; //温度S 示灯 sbit ledl=Pl 八 1; sbit led2=Pl 八 2; sbit led3=Pl八3; sbit hong=P2A0; CO sbit huo=P2Al; //天然气 sbit beep=P2A3; //蜂鸣器 sbit LCD_RS = P2 八5; //寄存器选择输入 sbit LCD_RW = P2A6; //液品读/写控制 sbit LCD_EN = P2 八7; //液晶使能控制 sbit LCD_PSB = P3A5; //串/并方式控制 /*变量定义*/ uchar i，a，b，c，d，e，f; //显示控制 uchar code dis[]={ uchar code dis 1[] = {?? 气体监控系统 }; uchar code dis2U = {’*2015-3-15 SUN”}; uchar code dis3[] = {时间: uchar code dis4[] = {制 :106 创作室n}; uchar code di$5[] = {CO: Safety}； uchar code dis6[] = {天然气:Safety’’}; uchar code dis7[] = {’’短信:Been sent}; uchar code dis8[] = {’’故障:Unresolved’’}; uchar code dis9[l = {HCO: DANGER}; uchar code dislO[] = {天然气:DANGER}; uchar code dis 11 [] = {短信:Not sent’}; uchar code disl2[J = {故障:Resolved ?’}; uchar code disl3[l = {A message is sen}; uchar code dis 14[1 = {ut,please wait...’}; uchar code digit[ ]={n0123456789H}; //走义字符数组S示数字 uchar sms_text[] = Carbon monoxide has exceed the standard; 短信内容 uchar sms_textl [J = Natural gas has exceed the standard; uchar s，m，h; //定义变量储存秒、分钟和小时 /*延时函数部分*/ /氺承氺承氺承氺:氺承氺氺氺氺氺氺氺氺氺糸氺糸氺氺氺糸氺氺氺氺氺氺氺:氺:{c氺:氺:氺:氺:氺:氺:氺:氺:{c氺 函数功能：延时1毫秒 void delay lms() unsigned char i，j; for(i=0;i20;i++) for(j=0;j33;j++); } r / rj^ rj^ rj^ rj^ 9^ rj^ rj^ rj* rj^ rj^ rj* rj^ rj* rj* rj^ rj^ rj^ rj^ rj* rj^ rj* rj* rj^ rj* rj^ rj^ rj* rj* 函数功能：延吋若干毫秒 入口参数：n 1? 1? ?X* ?￡* .X* .X* .X* .X* .X* ?9 f jw ^J* rjw rjw rjw ^J* rjw rjw ^J* rjw rjw jw ^J* rjw rjw j* ?了? j* ?:，j* *:? j* *:? ^2、*T* *:? j* ?了? j* ?:?，了**T* *? j* / void delay(unsigned char n) { unsigned char i; for(i=0;in;i++) delay lms(); } /*液晶驱动函数*/ Z*A? *1^ *? *1^ *? *1^ *? *1^ *? *1^ *? *1^ *A* *1^ *A* *1^ *A* *1^ *A* *1^ *A* *1^ *A* *1^ *A* *1^ *A* *1^ *A* *1^ *A* *1^ *A* 1^ *1^ *1^ *1^ *1^ *1^ *1^ *1^ *1^ *1^ *1^ *1^ *1^ *1^ / I ^T% Tw Tw Tw #T% T* #T% ^7^ #?% ^7^ #T% #7^ T% #7^ T% #7^ T% #7^ T% #7% #?% #7^ T% T% T^ ^T T% ^T T% ^