基于DSP的CAN总线通信及监测系统的设计-检测技术与自动化装置专业论文.docxVIP

基于DSP的CAN总线通信及监测系统的设计捅要 基于DSP的CAN总线通信及监测系统的设计 捅要 本文以导师的基金项目“故障诊断仪的研究与开发”为基础，进行了基于DSP的CAN 总线通信及监测系统的设计。采用了TI公司的TMS320F2812 DSP芯片作为本系统的主 控制芯片，以CAN总线为底层网络，通过USBCAN智能接口卡与上位机进行通信，利用 图形化的编程语言LabVIEW进行测试软件的开发，对通信数据进行监测。 硬件方面，以TMS320F2812 DSP为控制核心，设计了DSP系统的外围模块及CAN总 线通信模块的硬件电路。通过DSP内部集成的具有强大功能的CAN总线控制器(eCAN) 来传输数据，克服了传统RS-485总线的弊端。软件方面，在DSP的集成开发环境CCS 下，利用C语言，进行了软件的编程与调试。通过对CAN总线协议的制定，实现了与上 位机的实时通信。此外，论文还详细给出了监测系统中各个功能模块的程序框图以及自 定义的CAN总线应用层协议。 上位机的监测模块采用LabVIEW语言编写，简洁直观、操作简单、可靠性高、可维 ’护性好。该模块具有以下四个功能：即参数配置、数据传输、定时存储和实时显示等功 能。在测试过程中，通过监测界面显示出的测试信息，可了解整个系统的运行状态。模 块化设计与开发的方法，增强了系统的可靠性、稳定性，大大缩短了试验周期。 通过对本系统多次进行试验测试，该系统运行稳定，设计思路正确，实现了预期的 功能，能够实现通信功能和上位机监测功能，对于实际项目有着一定的实用价值。 关键词：状态监测，故障诊断，DSP，CAN总线，LabVlEW Des Des i gn of CAN Bus Commun i cat i on and Mon i tor System Based on DSP Abstract Combining with my director’S fund project The research and development of the fault diagnose instrument in Shan’xi province，this paper studied the design of CAN Bus communication and monitor system based on DSE Using the TMS320F28 1 2 DSP of TI company,the testing system takes CAN bus as bottom network to communicate with PC through USBCAN intelligent connection card．Finally it carries on the monitor to the correspondence data，and adopts the graphics programming language LabVIEW as the exploit tool of the software． In hardware，the electric circuit for those peripheral modules and the CAN bus communication module which takes TMS3 20F28 1 2 as core controller are designed．Powerful CAN bus controller,eCAN，is used to transmit data，which is integrated in the DSE CAN bus has lots of advantages over the RS一485 bus。The software is debugged in the CCS IDE and using C language．The system makes the function of real—time communication with PC by compiling and composing the application agreement of CAN bus．In addition，the program chart of every function module designed in the monitor system and the application agreement of CAN bus are given in this paper． The monitor module which is coded with LabVlEW langua