- 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
- 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
Page * LEU-MT TPG LEU-MT TPG Page * LEU-MT TPG TPG can be connected to the mains using the AC power pack for programming / charging TPG可连接AC电源屏进行编程/充电 -TPG can program with battery for approx. 8 hours (20?C) TPG使用电池编程可维持大约8小时(20?C) LEU-MT interfaces LEU-MT接口 Page * LEU-MT TPG Bluetooth Communication 蓝牙连接 please check bluetooth connection between TPG and handheld 请检查TPG与手持终端间的蓝牙连接 Page * LEU-MT TPG Menu菜单 Page * LEU-MT TPG Power Supply of Tesa Board Tesa板的电源供应 Tesa board can be supplied with power by the TPG Tesa板可由TPG供电 (necessary if the Tesa board is not supplied with power by the line / power supply can be enabled via the Tesa Diagnosis dialogue) (当Tesa板不通过外接电源供电时需要/供电可通过“Tesa Diagnosis” 启用) Proceed as follows to enable the power supply of the Tesa : Tesa供电启用过程如下: - Open the “Tesa Diagnosis” dialogue.打开“Tesa Diagnosis” 对话框 - Select “Tesa Power On”. 选择“Tesa Power On”. (The message Tesa Power switched on is displayed) (会显示“Tesa Power switched on” 信息) Open the “Tesa Diagnosis” dialogue 打开“Tesa Diagnosis” dialogue Note 注意 When the Tesa board is not supplied with power, the error message Tesa has not enough power. is displayed. 当Tesa板没有供电时,会显示错误信息提示Tesa has not enough power. ” Page * LEU-MT TPG Preconditions for Testing and Programming of Tesa Boards 测试和编程Tesa板的先决条件 Disconnect the 4-pole output cable from the Tesa board 从Tesa板上断开4芯(柱)输出线 2) Connect the TPG to the Tesa board using the cable 使用电缆连接TPG与Tesa板 3) Make sure that the TPG is switched on 确保TPG开着 4) Make sure that the handheld PSION Workabout Pro terminal is switched on 确保手持终端PSION开着 5) Make sure that Bluetooth communication is enabled 确保蓝牙连接启用 Caution 注意 Please refer to the safety instructions in the maintenance manual 请按照维护手册中的安全指令操作 Page * LEU-MT / Balise Programming Steps:Safety relevant data!LEU-MT/应答器编程步骤:安全相关数据 Program balise + MD4 check 给应答器编程+MD4检查 Check labeling of Balise检查标记 Labeling of balise标记 Install on track安装 Check MD4 with label and po
文档评论(0)