海康核心交换机配置及划Vlan副本.docx

6800 核心交换机配置 说明： 6800默认子板端口全部为 shutdown 状态（关闭 -不启用）， 双主控板一上电后，ACT灯亮为主控，不亮的为备用主控。 串口线接在主控板（ACT上。 配置命令如下： Switchenable Switch# Switch#config 备注：进入配置模式 Switch_config# 备注：配置子板 8（ 备注：配置子板 8（ 1-24# 口） 备注：启用子板 8（ 1-24#口） 备注：退出 备注：保存 Switch_config_if_range# Switch_config_if_range#no shutdown Switch_config_if_range#exit Switch_config#write 配置 VLAN 子板位 置 交换机端口 VLAN IP段 网关 备注 子板7 光口 1-12# VLAN71 子板7 光口 13-24# VLAN72 子板8 光口 1-12# VLAN81 子板8 光口 13-24# VLAN82 子板9 电口 1# VLAN71 方便客户搜索 IP 子板9 电口 2# VLAN72 方便客户搜索 IP 子板9 电口 3# VLAN81 方便客户搜索 IP 子板9 电口 4# VLAN82 方便客户搜索 IP 子板9 光口 5-12# VLAN91 子板9 光口 13-24# VLAN92 命令如下： Switch#。onfig Switch_con fig# int via n 71 Switch_con fig_v71#quit Switch_config#int vian 72 Switch_c on fig_v72#quit Switch_co nfig# in t vian 81 Switch_co nfig_v81#quit Switch_co nfig# in t vian 82 Switch_co nfig_v82#quit Switch_co nfig# in t vian 91 Switch_co nfig_v91#quit Switch_co nfig# in t vian 92 Switch_config_v92#quit Switch_config#write Saving current configuration... OK! 给端口配置 IP ： Switch_config#int range g 7/1 - 12 Switch_config_if_range#switchport pvid 71 % VLAN does not exist, Creating vlan 71. Switch_config_if_range#Nov 18 16:07:42 %LINE-5-UPDOWN: Line on Interface VLAN71, changed state to up Switch_config_if_range#quit Switch_config#interface range g 7/13 - 24 Switch_config_if_range#switchport pvid 72 % VLAN does not exist, Creating vlan 72. Switch_config_if_range#Nov 18 16:15:15 %LINE-5-UPDOWN: Line on Interface VLAN72, changed state to up Switch_config_g9/1#s Switch_config_g9/1#s Switch_config_if_range#Nov Switch_config_if_range#Nov 18 16:17:39 %LINE-5-UPDOWN: Line on Interface VLAN92, Switch_config_if_range#quit Switch_config#int range g 8/1 - 12 Switch_config_if_range#switchport pvid 81 % VLAN does not exist, Creating vlan 81. Switch_config_if_range#Nov 18 16:16:05 %LINE-5-UPDOWN: Line on Interface VLAN81, changed state to up Switch_config_if_range#interface range g 8/13 - 24 Switch_config_if_range#switchport pvid 82 % VLAN does not exist, Creating