印刷机报警信息英汉对照概要.docxVIP

{001 [] CIF30 input/output communication error}, 输入输出及通讯报警信息 . {002 [0E09] Auxiliaries circuits not active - W1}, 辅助启动没被激活 . {003 [0E12] Insufficient air pressure - W1}, 压缩空气压力不足 {004 [0E13] Insufficient main vacuum - W1}, 真空环境未满足 {005 [] The Machine is running}, 设备正在运行 {006 [0E05] Printer safety covers open (PRINT) - W1}, 安全门打开 (无法运行 ) {007 }, {008 [2E07] Oven safety covers open (OVEN) - W1}, 烘箱安全盖打开 {009 [1E03] Loader unit safety cover close (LOAD) - W1}, 上料安全门关闭 {010 [FILE] Error in accessing DATA file}, 获取数据文件有误 {011 [FILE] Error in accessing AXIS (axis parameter file)}, 获取轴参数文件有误 {012 }, {013 [Vis] Alarm vision system}, 视觉系统报警 {014 [Axis] Error with remote status request ELMO}, 报警与远程状态请求 elmo {016 [Axis] Check Elmo Manual; Error with ELMO MG }, 请检查第 4-2 elmo 手册 ;检查电机 {018 [] Machine A hasnt been reset}, 设备 A 无法复位 {019 [] Machine B hasnt been reset}, 设备 B 无法复位 {021 End of roll paper on left table}, 纸偏左 {022 End of roll paper on right table}, 台纸偏右 {023 Paper is cut on friction roll (left table)}, 左台纸剪切发生磨擦 {024 Paper is cut on friction roll (right table)}, 右台纸剪切发生磨擦 {027 [] Machine A hasnt been reset}, 设备 A 没有复位 {028 [] Machine B hasnt been reset}, 设备 B 没有复位 {030 [] Machine A Stopped}, 设备 A 停止 {031 [] Machine B Stopped}, 设备 B 停止 {032 [] Machine A in MANUAL mode}, 设备 A 在手动模式 {033 [] Machine B in MANUAL mode}, 设备 B 在手动模式 {034 [] Machine A in STEP by STEP mode}, 设备 A 在步进模式 {035 [] Machine B in STEP by STEP mode}, 设备 B 在步进模式 {049 [1E06] Up sucker sensor (LOAD) - W0}, 上料抓手上位传感器 {050 [21MG] Print Table Axis Homing}, 旋转电机复位原点 {051 [22MG] Print Head X Axis Homing}, 印刷头 X 轴复位原点 {052 [23MG] Print Head Y Axis Homing}, 印刷头 Y 轴复位原点 {053 [24MG] Print Head THETA Axis Homing}, 印刷头 THETA 轴复位原点 {054 [25MG] Print Head Z Axis Homing}, 印刷头 Z 轴复位原点 {055 [26MG] Squeegee Input/Output Axis Homing}, 刮刀前 /后复位原点 {056 [27MG] Squeegee Up/Down Axis Homing}, 刮刀上 /下复位原点 {061 [10MG] Print Walking Beam Axis Homing}, 印刷上料行走臂电机复位原点 {062 [28MG] Oven Walking Beam Axis Homing}, 烘箱行走臂电机复位原点 {063