JBT 7185.4-1995冲模滑动导向钢板模座 四导柱上模座.pdf

中华人民共和国机械行业标准JB/T 7185. 4--95冲模滑动导向钢板模座“四导柱上模座·主题内容与适用范围本标准规定了冲模滑动导向钢板模座·园导柱上模座的技术条件、尺寸规格、材料、热处理要求及标记。本标准适用于冲模滑动导向钢板模架，引用标准JB/T 7188冲模钢板模架零件技术条件GB 699优质碳素结构钢技术条件GB 700碳素结构钢GB 8845冲模术语3模座的技术条件和尺寸规格3. 1技术条件按JB/T7188的规定。3. 2尺寸规格见图和表。TA其余1.6IT/BOD.图机械工业部1995—03—21批准1995—07—01实施52 JB/T 7185..4-95表mm凹模周界D(R?)D, (H7)L1BHF.s.St基本 极限:基本极限S:IxWL.8尺寸偏差尺寸偏差16016025032.40 80170373820020025032401201703738250100.2502503240170170378831531526540452251754245155M12X25400.40026540453101754220026532401201853738一25025028040451601904245100+0.025+0.025315125315.280.4045225190.4245015540040028040453101904245240.5005002804045410190424533025025031540451602254245100315.3153154045225225 4245155°40040031540453102254245160230M12 X 2550050031540454102254245330+0. 0300800+6306303555055520245525543002502503554045.1602654245100315315355404522542+ 0. 025+ 0. 0252650.45150: 040020040035540452654245230500 .50040050553902905255300+ 0. 0301+0: 0306306304005055520290520550430M16X 30+0. 025+0.02531531542545225 -335424515000M12X 25400:400:4505055290340525520025050050045050ss39034052550086306304505055520+0.0303405255+ 0. 0300430M16X308008004505055690340525560040040053050552904205255200500500560506337443462+0.03065300315+0.030560M16×306306305095044346206504308000085606363674434626555053 JB/T 7185.i4--95续表D(R?)D,(H7)哲棋周养基本极限SrMXtH基本极展T尺寸偏差尺寸偏差6337450462652805005006305010800+M16X 305045046265 3806306306306363+400635046265550800800630674+0. 03510006708070860.530.76807001000050 0++ 0. 030635046246265380630630750630M20× 3550080075080706606107680500800+0. 035807086061076807001000100075070.86076076807001000630100090008.材料和热处理要求4.1 材料.45 钢 GB 699 .凹模周界 L×B,小于 400×250的滑动导向模座可用Q235—A钢 GB700.4.2热处理要求45 钢调质 HRC26~ 30.标记5本标准规定的模座标记由下列要素组成上模座，a.模座的凹模周界 LXB;0.模座厚度 H：d.材料;本标准编号。示例：凹模周界 L400 mm、B=250 mm、模座厚度 H=40 mm、材料为 45 钢的四导柱上模座的标记如下：上模座 400×250×40.45JB/T 7185.4