镜头光学设计.pptVIP

鏡頭光學規格的介紹Curtis主題1

Curtis內容大綱1PixelSize2ImageSize3ImageCircle4LensComposition5FieldOfView(FOV)6FNumber7Relativeillumination(RI)8ChiefRayAngle(CRA)9Distortion10MTF11EFL12BackFocusLength(BFL)13OpticalTotalLength2

LCM-****2Mega(Design)ItemLCM-****SensorMI-XXXX，OV-XXXXPixelSize3.2x3.2μmImageSizeD:5.6mm(H:4.48V:3.36)ImageCircleφ5.9mmLensComposition1G3PFieldOfView59.5゜(atSENSORDiagonal)FNumberF/2.8Relativeilluminationat100%ofImageHeight55%(atSENSORDiagonal)ChiefRayAngleD:19.7゜H:20.6゜V:20.5゜TVDistortion1%MTFCenterCenter54%@180LP/mm50%@200LP/mmat70%ofImageHeighth=70%T61%/S74%@90LP/mmat80%ofImageHeighth=80%T59%/S69%@90LP/mmat90%ofImageHeighth=90%T58%/S63%@90LP/mmat100%ofImageHeighth=100%T59%/S72%@90LP/mmFocusLengthf=4.87mmBackFocusLength1.494mmOpticalTotalLength6mmIRCF650±15nm@50％SPEC.Curtis未來發展3

CurtisBFL基本光學系4

1、Imagecirclesensorsize(D)。2、D+0.4mm(Package公差)。MEMO：光學設計的考量，要從了解SENSOR開始。光學設計需與SENSOR達到最佳配合。PLWDP=Pixelsizesensor1Curtis5

sensor2Curtis尺寸表6

FOV:FieldOfViewDθθfFOV=2θ=2tan-1[D/2f]FOVsensor例：SENSOR對角線D=5mm，焦點距離f=3mm，則FOV為：FOV=2θ=2tan-1[5/2*3]=79.6(度)Curtis7

F/#_1DfsensorF/#：決定光通量、影像的亮度。F/#=f/DI0∝1/(F/#)2………(進光量與F/#平方成反比)。I0≡ImageIntensity流明≡照度MEMO：F/#數值愈小→設計上困難度愈高。FOV愈大→設計上困難度愈高。Curtis8

F/#_2．F/2.8比F/4.0亮度亮兩倍。例：F/#=2.84，焦點距離f=50mm，則入光大小為：F/#=f/D；D=f/F/#1、D(F/2.8)=50/2.8=17.862、D(F/4.0)=50/4.0=12.51、D(F/2.8)=50/2.8=17.862、D(F/4.0)=50/4.0=12.5．以圓面積計算公式計算如下：(πR2)1、3.14*17.862≒10022、3.14*12.52≒491(面積F/2.8)≒2*(面積F/4.0)Curtis9

F/#_3．CCD靈敏度較CMOS為高。不致能區線性區飽和區exposureresponseMEMO：CCD所使用的F/#值較大(即光圈較小)。如果使用過大的光圈，則會落於飽和區使得成像品質不好。Curtis10

MTF1黑白Co≡(Bmax–Bmin)/(Bmax+Bmin)=contrast代表的是層次感、立體感。Lensdesign→Good