油封钢圈拉深模具毕业设计：.doc

摘 要 本设计为油封钢圈拉深模具设计，油封钢圈是固定油封并使油封有足够密封空间的一种冲压件。查询阅读阅相关的书籍资料然后再根据零件的尺寸、材料、生产批量等的要求，分析零件的工艺性。最终得出使用集落料拉深冲孔的复合型模具制造该零件，才能最大的提高生产效率和保证产品的质量。设计当中首先分析零件的工艺性后确定排样和裁板，计算压力中心和所需的冲压力后再选择压力机，然后计算凸、凹的零部件和最终的设计选择所需模具刃口尺寸及公差后就对压力机进行校核，选择所需要标准件后绘制模具装配图。在结构设计中，是对落料凹模、卸料板、冲孔凸模、落料拉深凸凹模和拉深冲孔凸凹模进行结构设计。根据设计计算结果再查询相关标准选用冲压机、模架、定位元件、卸料元件与出件元件、紧固件后完成模具设计。 关键词：复合模；落料凹模；拉深冲孔凸凹模；模架 Abstract The design for the steel ring seal design drawing die, seal rims and to seal seal is fixed there is a sufficient seal stamping space. Access to relevant information and then depending on the size of parts, materials, production and other requirements, process analysis part. Final results using colony Deep Drawing Punching mold for manufacturing the composite parts, in order to improve production efficiency and the greatest guarantee the quality of the product. Designs to determine the first part of the analysis process of nesting and cutting board, calculate the center of pressure and pressure and then select the desired punch presses, then calculate the convex and concave mold edge dimension and tolerances required for the final design selection to zero, parts, and then be checked against the press, drawing mold assembly drawing. Which in structural design, mainly blanking die, punch punching, blanking drawing and drawing punch punch punch structural design. According to the standard selection of design calculations and positioning components, unloading and the pieces of equipment, mold, stamping equipment, fasteners, and ultimately complete mold design. Key words：Composite modulus;Blanking die;Drawing punching punch;Mold 目 录 中文摘要 1 英文摘要 2 引 言 5 1 零件工艺分析 6 1.1设计题目 6 1.2 材料分析 6 1.3 结构分析 6 1.4 精度分析 7 2 冲裁工艺方案的确定 8 3 冲模结构确定 9 3.1 模具的结构形式 9 3.2 模具结构的选择 9 4 工艺设计计算 10 4.1零件毛坯尺寸计算 10 4.1.1确定修边余量 10 4.1.2计算毛坯直径 10 4.2 确定拉深次数 10 4.3 排样设计与裁板方案的确定 10 4.4 计算冲压力与压力中心，初选压力机 11 4.4.1落料工序冲压力 11 4.4.2拉深工序冲压力 12 4.4.3冲孔工序冲压力 12 4.4.4计算总冲压力，压力中心，选择压力机 13 4.5 拉深凹，凸模圆角计算 14 4.6 计算模具刃口尺寸 14 4.6.1落料工序中刃口尺寸计算 14 4.6.2 拉深工序中刃