网站大量收购独家精品文档,联系QQ:2885784924

HP StorageWorks MSL2024 Tape Library getting started (AK378-96028, March 2010).pdf

HP StorageWorks MSL2024 Tape Library getting started (AK378-96028, March 2010).pdf

  1. 1、本文档共12页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
HP StorageWorks MSL2024 Tape Library getting started (AK378-96028, March 2010)

HP StorageWorks MSL2024 Tape Library getting started ? Copyright 2010 Hewlett-Packard Development Company, L.P. Seventh edition: March 2010 The information in this document is subject to change without notice. Printed in the US *AK378-96028* IMPORTANT: The shipping lock must be removed for the robotics to work properly. A robot move error is displayed if the shipping lock is not removed. See Step 1, Removing and storing the shipping lock. WARNING! The Library weighs 15.6 kg (34.3 lb) without media and 20.4 kg (44.9 lb) with media (24 cartridges). When moving the Library, to reduce the risk of personal injury or damage to the device: ? Observe local health and safety requirements and guidelines for manual material handling. ? Remove all tapes to reduce the overall weight of the device and prevent cartridges from falling into the robotic path and damaging the Library. ? Obtain adequate assistance to lift and stabilize the device during installation or removal. WARNING! When placing the Library into a rack, to reduce the risk of personal injury or damage to equipment: ? Extend the rack leveling jacks to the floor. ? Ensure that the full weight of the rack rests on the leveling jacks. ? Install stabilizing feet on the rack. ? Extend only one rack component at a time. Racks may become unstable if more than one component is extended. Front panel overview 2. Mailslot1. Power button 4. LCD screen3. LEDs 6. Air vents5. Control keys 7. Magazines Page 1 Back panel overview: parallel SCSI 2. Fan1. Parallel SCSI connector 4. Tape drive assembly3. Power connector 6. Serial port (Factory use only)5. Ethernet port 8. Magazine release hole7. USB port 10. Tape drive assembly LED9. Pull-out tab containingproduct information NOTE: The overview of libraries with full-height SCSI drives is similar to that of libraries with half-height SCSI drives, shown above. Back panel overview: SAS 2. Fan1. SAS port 4. Tape drive assembly3. Power connector 6. Serial port (Factory use only)5. Ethernet

文档评论(0)

l215322 + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档