英文任务书.doc

-RIH with following BHA 按以下钻具组合下钻 121/4″ bit+junk sub（打捞杯）+18×8″DC+ 12×5″HWDPs+5″DPs -Tag CMT inside casing(580m±)探水泥塞 -Circulate at top of CMT探至水泥塞后循环 -Drill CMT and CSG shoe down to 622m钻水泥塞及管鞋，钻至H622m -Circulate at 622m call company man carry out shoe bond test at 2Mpa(close pipe ram,use rig pump)在H622m循环叫监督。做地破实验2Mpa（关单闸板，用泥浆泵试压） -Drill down to 645ms call company man for further program钻至645m后，监督安排下部工作 -RIH care fully down to 620ms(bit out of CSG shoe)下钻至620m（钻头出套管鞋时小心操作） -Circulate at 620ms.60SPM only to shear DHPA mud consult mud engineer 循环，叫泥浆工程师 -Ream down to bottom 120RPM-60/70 RPM划眼至井底 泵冲120 转速60/70 -Tag bottom without rotation and mark bottom on D pipe不旋转探至井底后在钻杆上标注 -Pick up 0.4m rotate string 80RPM 提离井底0.4m，转动钻具（转速80） -Slowly tag bottom,increasee SPM to 135/140慢慢下至井底 泵冲135/140 -Start drilling WOB 2tons,RPM100开始钻进钻压2吨，转速100 -Drill DOWN TO 652m钻至652m -Increase WOB to 4 tons and 150RPM.增加钻压至4吨，转速150 -Continue drilling down to CSG TD.钻进 -Ream every single drilled.每钻进一单根划眼一次 -Inclination survey after every 100ms.每钻进100m测斜一次 -Record RSPP(Reduced Strokes Pump Pressure) after every 100ms 每钻进100m作低泵冲实验 Revised drilling program 修正钻井任务书 -POOH,lay down PDC bit carefully in plastic consister起钻完倒PDC钻头放在塑料垫子上 -RIH with following BHA按以下钻具组合下钻 121/4″ bit+junk sub（打捞杯）+N.B stab（近钻头稳定器） +1×8″DC+S.stab（钻柱稳定器）+2×8″DCs+ S.stab （钻柱稳定器）+12×8″DCs+D.jar（震击器）+3×8″DCs +X-over+12×5″HWDPs+5″DPs -Stop at 618ms,circulate to shear mud,ream down to bottom下钻至H618m，循环处理泥浆，划眼至井底 -Work on Junk sub 打捞 -Resume drilling ,drill 2ms with WOB4/5 tons SPM135 RPM90继续钻进，钻进2m（参数：钻压4/5吨 转速90 泵冲135） -Gradually increase weight on bit to 10tons and RPM 120逐渐增加钻压至10吨，转速120 -Further program will be communicated下步工作与监督联系 Bit type（钻头型号） MA4N make 厂家security Jets（喷嘴） 16×16×16 Do not use，If junk sub is double box 如果打捞杯是双母的就不下 Drilling program 钻井任务 PDC BIT TYPE BS103 PDC钻头型号BS103 Size 121/4″SER#105742 -RIH carefully下钻仔细操作 -If under gauge hole observed ,do not push bit through undergauge hole.(Max slac