钢结构防火涂料的涂装验收方法（Acceptance method for coating of steel structure fire retardant coating）.docVIP

下载本文档

10
0
约2.78万字
约 18页
2017-07-21 发布于河南
举报
版权申诉

钢结构防火涂料的涂装验收方法（Acceptance method for coating of steel structure fire retardant coating）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

钢结构防火涂料的涂装验收方法（Acceptance method for coating of steel structure fire retardant coating）

钢结构防火涂料的涂装验收方法（Acceptance method for coating of steel structure fire retardant coating） [Chinese coating network] abstract: visual inspection method is used to detect the variety and color of paint and compare with the selected samples. Detection of coating color and leakage and fracture by visual method; Test the strength of the coating with 0.75 ~ 1kg hammer. Test the coating flatness with 1m straight. The coating shall meet the following requirements: 1. The variety and color of the paint are detected by visual inspection, and the sample is compared with the selected samples. Detection of coating color and leakage and fracture by visual method; Test the strength of the coating with 0.75 ~ 1kg hammer. Test the coating flatness with 1m straight. Thick coating steel structure fire retardant coating shall meet the following requirements: 1, the coating thickness conform to the requirements of the design, thick bottom is lower than the original standard of not less than 85% of the original standard, area and thickness of parts of a continuous length is not greater than 1 m, and such things will not appear within 5 m; 2. The coating should be completely continuous, and should not be exposed or omitted; 3. Between the coating and the steel substrate and the coatings should be bonded firmly, with no empty drum, loose and loose, etc.; 4. The surface of the coating should be free of bulging, where there is a requirement of appearance, the deviation should not be greater than 8mm for the non-straightness and roundness of the bus. The coating should meet the following requirements: 1. The coating thickness should meet the design requirements; 2. No leakage, powder and obvious cracks, etc., if there are individual cracks, its width is not greater than 0.5mm; The bonding between the coating and the steel substrate and the coating shall be strong, the absence of the strip, the empty drum, etc. Color and appearance comply with the design rules, the outline is clear and the stubb