pcb治具设计、制造和管理（PCB jig design, manufacture and management）.docVIP

下载本文档

9
0
约8.61千字
约 8页
2017-07-23 发布于河南
举报
版权申诉

pcb治具设计、制造和管理（PCB jig design, manufacture and management）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

pcb治具设计、制造和管理（PCB jig design, manufacture and management）

pcb治具设计、制造和管理（PCB jig design, manufacture and management） Abstract] the jig is a kind of special clamp designed for the PCB electric plate model and used for the electrical performance breaking test. It is divided into one side jig and double sided jig. In high precision PCB production, to test its power using universal fixture, fixture to manufacturing and testing have brought certain difficulties, there is also trouble back current driving reliability and load line testing technology. Our company designs the general test jig, can adapt to the high accuracy printed circuit board electrical performance test, the test reliability achieves 100%, thus saves the jig manufacture expense. 1. jig design The 1.1 tool process steps The formation of computer graphics - aperture separation and circuit wiring diagram form NC NC file to the surface of the drilling tool the assembly of the jig the layout of the needle the wiring the jig installation and the inspection the management Selection of 1.2 probe specifications: Phi 0.45mm, Phi 0.65mm, Phi 0.90mm, Phi 1.40mm, Phi 1.70mm Methods 1.3 fixture layout 1.3.1 IC used meaning wrong method of selected points (IC, width 0.15mm, pitch 0.15mm, total 128 feet IC, There are three IC boards with different PCB positions for example; if the IC surface can not use 1.2 specifications of the probe, it can also use conductive adhesive. A graph with three or more points of divergence on the same line of 1.3.2. If the pads and wires are so close that they can not be clearly distinguished, they do not serve as a bifurcation point. 1.3.3 a line of two or more pads at either end or center of the wire is used only as a check point at both ends of the wire. The height of the jig is 6cm; the height of the double sided board is 3.56cm; the top is 4.5-3.5cm; and the composite jig with 6cm can also be used. 1.5, the use of 3 pieces of epoxy plate and 2 transparent film structure 1.6 plate fixture manufacturing 1.6.1 when the CNC NC file is released, te