液晶显示器常见pwm 芯片和高压板专用芯片去保护的方法（Liquid crystal display common PWM chip and high voltage board special chip protection method）.docVIP

下载本文档

7
0
约5.98千字
约 7页
2017-08-03 发布于河南
举报
版权申诉

液晶显示器常见pwm 芯片和高压板专用芯片去保护的方法（Liquid crystal display common PWM chip and high voltage board special chip protection method）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

液晶显示器常见pwm 芯片和高压板专用芯片去保护的方法（Liquid crystal display common PWM chip and high voltage board special chip protection method） [pin function] Drive output 1. The foot output square wave excitation signal can be externally connected with the gate of the field effect transistor. Power supply terminal. The pin voltage exceeds the undervoltage lockout threshold (4.5V), and the internal circuitry of the chip can be activated normally. Timer setting. The foot is provided with a timing time through an external resistance and capacitance component for internal shutdown and protection circuit adoption. Brightness control terminal. The foot according to his feet set, you can enter the PWM pulse width modulated signal or DC voltage signal to control the brightness of the lamp tube. Lamp current detection. When the lamp tube is lighted, the voltage of the foot is greater than 0.7V, and the integrated circuit enters a normal operation mode, and the pulse width modulation brightness control circuit starts. If the voltage of the foot is zero after the circuit is started, the protection circuit starts to act and the chip stops encouraging the output of the signal. Therefore, the short-circuit current can not be used to determine whether there is over-current fault. The feedback voltage detection. The foot accepts the feedback voltage from the high frequency transformer and increases the voltage if the CCFL lamp is damaged or disconnected. The limit voltage is 3.0V, and when this value is reached, the actuating signal is turned off. The foot and foot voltage exceeds the user set voltage protection circuit will start. The overcurrent protection value setting. The overvoltage and overcurrent protection action threshold can be set by the resistor divider network that is connected with the pin. The empty feet To empty the foot The enable end. When the voltage of the pin is greater than 2V, the internal circuit is started and the internal circuit is closed when less than 1V. 2 dimming mode se