T形单梁计算全英文课程设计.docVIP

下载本文档

2
0
约1.86万字
约 15页
2017-08-14 发布于湖北
举报
版权申诉

T形单梁计算全英文课程设计.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

T形单梁计算全英文课程设计

Design information Simple supported beam with span 31m and the calculated span is 29.66m Design load: vehicle load:grade Ⅰ, pedestrian load: 3.0,coefficient for important of the structure: . Environment: bridge is located in the wild general areas, grade Ⅰ environment, annual average relative humidity 75%. Material: prestressed reinforcement uses eliminate stress spiral rib wire bundle, characteristic value of tension strength ; design value of tension strength , elastic modulus ;BBRV anchorage. Non-prestressed reinforcement: HRB400, characteristic value of tension strength , design value of tension strength . When diameter , use HRB335, characteristic value of tension strength, design value of tension strength. Elastic modulus of steel is . Concrete: C50 for main girder, , characteristic value of compression strength, design value of compression strength; characteristic value of tension strength, design value of tension strength. Design detailing: according to JTG D62—2004, design as full prestressing concrete structural. Construction methods: posttensioning, pre-stressing ducts use embedded metal bellows forming, wire bundles tensioned at both side at the same time with jacks; cast in place 400mm wet-joint. Finally pave 400mm asphalt deck pavement. Dimension of main girder Dimension of all parts of main girder is shown in the chart ( units:mm): Section property of main girder Calculation of effective width of compression flange So effective width of compression flange is Calculation of section property (summation block) Section property of mid-span and L/4 span Number Area (mm2) (mm) (mm3) (mm) (mm4) (mm4) b (mm) h (mm) ① 360000 90454 1000 180 ② 96000 220324 800 120 ③ 320000 800 256000000 -256 200 1600 ④ 20000 1533-989 100 200 ⑤ 80000 1700 136000000 -1156 400 200 Sum 876000 544 476180000 1256 Section dimension and property of mid-span and L/4