k1000tii系统软件更改跟踪记录（K1000tii system software change tracking record）.doc

下载文档 降价啦

0
0
约4.37千字
约 7页
2017-08-20 发布于河南
举报
版权申诉
保障服务

k1000tii系统软件更改跟踪记录（K1000tii system software change tracking record）.doc

1、本文档共7页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

k1000tii系统软件更改跟踪记录（K1000tii system software change tracking record）

k1000tii系统软件更改跟踪记录（K1000tii system software change tracking record） K1000T_STANDARD software change tracking record *************************************************************** *************************************************************** Version number: K1000T_STANDARD_3.0 (2007516) ********************************* Change the base to K1000T_STANDARD_2.0_2007.3.23 Changes: 1, upgrade processing for K1000T_STANDARD_2.0, as standard version of the system. 2 、 increase the function of M21 and M23, and the function is same as that of curing PLC.. Increase the corresponding control parameters K6.1, K6.2. M21P is replaced by the M71 directive; M21Q is replaced by the M72 command; the M23P is replaced by the M73 command; the M23Q is replaced by the M74 command; P specifies the time set by T24 and T25. Change the original input point of X3.7 3, X0.7. Yaxing turret 4, global turret of the original output point Y1.6, changed to Y2.6. 5, increase the boot program switch status 1: to open 0: for the pass 6, increase the workpiece count, power down maintenance function 1: keep 0: do not keep 7, to correct the 2 version of the protective door open, do not clear the S code output problems. 8, to correct the 2 version of the protective door after opening, cancel the protective door function, can not start the spindle problem. 9, correction 2 version, count to reach the output, cancel count, output function will always remain suspended. 10, the 2 version of M10, M11, QPS, QPJ output control by the chuck function parameters control canceled. Release date: 2007516 *************************************************************** *************************************************************** Version number: K1000T_STANDARD_3.0 (2007711) ********************************* Change the base to K1000T_STANDARD_3.0_2007.5.16 Change content: 1, increase the choice of stop button function, jump button function, compatible with the previous version. Release date: 2007711 *******************