高液限粘土压实特性及强振碾压工艺分析-analysis on compaction characteristics and strong vibration compaction process of high liquid limit clay.docxVIP

  • 5
  • 0
  • 约4.41万字
  • 约 68页
  • 2018-07-05 发布于上海
  • 举报

高液限粘土压实特性及强振碾压工艺分析-analysis on compaction characteristics and strong vibration compaction process of high liquid limit clay.docx

高液限粘土压实特性及强振碾压工艺分析-analysis on compaction characteristics and strong vibration compaction process of high liquid limit clay

论文独创性声明本人声明:本人所呈交的学位论文是在导师的指导下,独立进行研究工 作所取得的成果。除论文中已经注明引用的内容外,对论文的研究做出重 要贡献的个人和集体,均已在文中以明确方式标明。本论文中不包含任何 未加明确注明的其他个人或集体已经公开发表的成果。本声明的法律责任由本人承担。论文作者签名:年月日论文知识产权权属声明本人在导师指导下所完成的论文及相关的职务作品,知识产权归属学 校。学校享有以任何方式发表、复制、公开阅览、借阅以及申请专利等权 利。本人离校后发表或使用学位论文或与该论文直接相关的学术论文或成 果时,署名单位仍然为长安大学。(保密的论文在解密后应遵守此规定)论文作者签名:年月日导 师 签 名:年月日摘要在公路工程的路基填筑过程中,填土的使用非常广泛,而这些填土都要经过压实, 以减少它的沉降量,降低其排水性能,提高其抗剪强度。填土质量的好坏直接影响着地 基、路基的质量,而且还往往是上部结构变形、沉降、破坏的最直接的原因。因此,路 基的压实工作,是路基施工过程中一个必不可少的重要工序,也是提高路基强度和稳定 性的一个根本技术措施。在现场施工遇到高液限粘性土,当采用直接填筑施工的技术时,由于它的含水量过 高,有时候为了施工工期的要求,或者是因为种种原因的限制,不能使土体的含水量减 下来,在这种情况下用普通的压路机去压实时,往往达不到规范规定的压实标准,另外 随着科学技术的发展,出现了更多的压实设备,规范中规定的压路机的压实厚度已经不 能适应发展的需要,这些问题在本文中都有涉及。本文在国内外关于压实度的研究基础上,对高液限粘土压实的成因、影响因素及压 实机理进行了较为系统的分析和研究。结合江西境内吉莲高速公路上的路基压实的现场 试验,先是在实验室对试验用土的基本物理性质进行了研究,在此基础上在实验室内用 试验探讨了试验用土的力学性质与压实度之间的关系,后又在现场试验的基础上,比较 大激振力压路机与普通压路机的压实效果,并指出了它们对粘性土的合理压实厚度,从 而在施工时保证压实质量的前提下,可以大幅度地缩短工期、加快施工进度,对施工现 场的路基压实具有一定的指导意义。关键词:压实度、力学性能、合理压实厚度、压实效果、现场试验AbstractFilling soil is used widely in filling the subgrade. After compaction of the filling soil , its settlement is reduced , drainage performance is weakened , and shear strength increases.Filling quality has a direct impact on the foundation and roadbed, it sometimes can lead to the deformation, sedimentation and destruction of the superstructure. Therefore, compaction of subgrade is an essential one of roadbed construction process, and also a fundamental technical measures to improve the subgrade strength and stability.For the high liquid limit clay on construction site, when using direct filling construction technology, its water content is too high to cut down. In this case, using the ordinary roller fail to meet the compaction standard. With the development of science and technology, more compaction equipment are brought in. The compacted thickness of roller in specification can not meet the development needs, these issues are involved in this paper.In this paper,the compaction causes, influencing factors and mechanism of the wereanalyzed and

您可能关注的文档

文档评论(0)

1亿VIP精品文档

相关文档