添加荆含量对麦秸／聚乙烯微发泡复合材料加工与耐水性能影响.docVIP

添加荆含量对麦秸／聚乙烯微发泡复合材料加工与耐水性能的影响-园林 添加荆含量对麦秸／聚乙烯微发泡复合材料加工与耐水性能的影响 doi：10.13360/j.issn.1000-8101.2015.04.027中图分类号：TQ328.2；TB332 高振棠1，蔡红珍2* （1.济宁市技师学院，山东 济宁 272000；2.山东理工大学） 摘要：通过改变麦秸粉和AC发泡剂添加剂含量，考察口模压力降，测定复合材料加工流动性及试样吸水性，研究添加剂含量对麦秸/聚乙烯复合材料加工与耐水性能的关系。将高密度聚乙烯与麦秸粉混合，经异向锥形双螺杆挤出机和片材口模成型加工麦秸/聚乙烯复合材料试样。结果表明：口模挤出压力降受麦秸粉、AC发泡剂用量的影响较大；麦秸粉用量低于40份时对复合材料体系的加工流动性影响不大，当麦秸粉用量高于40份时，麦秸粉的流动性较差，会严重阻碍链段的运动，导致复合材料的流动性下降；复合材料的24 h吸水率随麦秸粉用量的增加而增大。 关键词 ：挤出工艺参数；吸水性；微孔发泡 Effects of additive content on process and water resistance properties of wheat strawPE microcellular foaming composites ∥ GAO Zhentang， CAI Hongzhen Abstract：The wheat strawpolyethylene （PE） composite samples were prepared by using a special die molding and the conical twin screw extruder. The pressure drop of die at different contents of wheat straw powder and AC blowing agent was investigated， and processing fluidity and water absorption of the composites were tested. The influence of additive contents on processing and water resistance properties of the wheat strawPE composite was also studied. The results showed that the pressure drop of die was greatly influenced by the contents of AC blowing agent and straw powder. When the wheat straw content was under 40 copies， its influence on the processing fluidity was not significant. Above the 40 copies， the fluidity of wheat straw was significantly reduced， which seriously hindered the chain movement and led to the drop of composite fluidity. The 24 h water absorption rate of the composite increased with the increase of wheat straw content. Key words：extrusion process parameters； water absorption； microcellular foam First author’s address： Jining Technician College， Jining 272000， Shandong， China 收稿日期：2014-12-13 修回日期：2015-01-21 基金项目：国家农业科技成果转化资金项目（2013GB2C600274）。 作者简介：高振棠（1974-），男，讲师，研究方向为生物质基复合材料。通信作者：蔡红珍，女，副教授。Email： [emailprotected] 微孔发泡木塑复合材料就是将塑料、植物纤维、矿物填料、助剂、改性剂和发泡剂等原料按质量比混合，经木塑成型设备加工而成的泡孔均匀分布的复合材料，广泛应用于建筑装修、景观园林、家具生产和汽车内饰件等领域［1］。微孔发