《油底壳的加工工艺与编程》-毕业论文（设计）.doc

┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ 装 ┊ ┊ ┊ ┊ ┊ 订 ┊ ┊ ┊ ┊ ┊ 线 ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ 毕业设计（论文）报告纸 PAGE PAGE 14 毕业设计说明书 课题名称 油底壳的加工工艺与编程 二级学院（系）/专 业 机械工程系/模具设计与制造 班 级 模具0811 学 号 0801423101 学生姓名 贲晶 指导教师： 匡余华 2010 年 05 月 14 日 摘 要 本课题进行490T油底壳体加工，首先是对壳体零件工艺设计，在分析了490T油底壳的具体结构及技术要求的基础上，详细制定了两种壳体加工整体加工工艺路线，并比较其优劣选择最优的方案进行加工。根据各道工序的技术要求，选定各道工序的背吃刀量、进给量、切削速度以及所采用的机床、刀具、夹具等，确定各道工序的时间定额，从而绘制工艺过程卡片。然后对精铣前后端面专用夹具体进行设计，根据被加工零件的结构特点、加工内容的尺寸和精度要求，确定加工中心的配置方案，对专机进行总体设计－三图一卡即为零件工序图、机床联系尺寸图。 Abstract This topic carries on design with the combined milling machine in the ZS1105 diesel oil enginr case body, the main content divided into: First, about box body parts process planning, at the base of analyzing the ZS1105 diesel oil enginr case bodys concrete structure and the technological specification. I formulated two kind of box body processing process route in detail, and compared them to choose the most superior process route to carry on the processing. According to each procedures specification. I designated the penetration of a cutting tool, the feed quantity, the cutting velocity as well as, the cutting tool, the jig and so on, which determine the time quota, and make the process card. Second, about modular machine-tool design, according to the unique feature of the components, the processing content size and the accuracy requirement, I determined that combined milling machines disposition plan, carried on a system design - three drawings and one card namely the components working procedure chart, the processing schematic drawing, the tool relation dimensional drawing and the tool productivity computation card design. Third, I drawled the assembly drawings of hydraulic slider and detail drawings.  目 录 TOC \o 1-3 \h \z \u 摘 要 2 第一章 绪论 5 第二章 零件加工工艺 7 2.1概述 7 2.2工艺方案制定的基本原则及注意问题 7 2.3 490T 油底壳的加工工艺路线编制…………………………………………………8 第三章 加工中心加工大平面和四周面………………………………………………16 结 论 17 致 谢 18 参考文献 19 附件…………………………………………………………………………………….20 第一章 绪论 毕业设计是培养我们理工科学生的一个