哈飞汽车研发中心制图标准汽车线束CAD图示方法.docxVIP

HHMC HFD1-2003 HFD-1-2003 CAD 2003-10-18 2003-11-1 Page 1 of 21 HHMC HFD1-2003 目 次 适用范围·································································3 图示方法总则·····························································3 2.1 各零件图示方法·····················································3 2.1.1 电线束·························································3 2.1.2 接头及端子·····················································4 2.1.3 管类···························································5 2.1.4 胶带···························································6 2.1.5 其它安装件·····················································10 2.2 节点代号表示方法····················································11 2.3 功能代号的表示法····················································12 2.4 回路代号的表示方法··················································13 2.5 插接件的表示方法····················································13 2.6 尺寸标注····························································13 2.7 尺寸公差的标注······················································16 2.8 端子表面处理及材料标注··············································16 2.9 回路表的表示方法····················································16 2.10 接点可能区间的表示方法·············································18 2.11 附录 1 插接件符号缩略代号的编写说明·································19 2.12 附录 2 线束图中功能代号编制说明·····································21 Page 2 of 21 HHMC HFD1-2003 1．适用范围 本标准是线束成品图采用计算机绘制的图示方法的规定。如本标准内容和图纸内容不同时，优先采用图纸规定。 2．图示方法总则 ·各零件用简略符号图表示。 ·有必要采用三唯图时，采用素描图形式。 ·多部件采用同一张图纸时，利用功能代号的区分。 2.1 各零件图示方法 2.1.1 电线束 电线束无论是干线、支线都用一根较粗实线表示。 1).导线种类（按耐热区分） 线种类如表 1 所示: 表 1 CAD 图 含义 普通电线 相当 AVX 线 相当 AEX 线 2).分支线 原则上，分支线用图 1 所示的方法表示。 备注： 符号 是表示用胶带缠绕端点的图例。 图 1 2.1.2 插接件及端子 1）.插接件及端子排列都用图 2 所示的 A 向视图（从入线方向看的排列）表示。有锁止机构的插接件，应将锁止机构部分向上观察。 2 Page 3 of 21 HHMC HFD1-2003 2). 1 3). 2 4). 2 3 2 NATURAL RED BLACK BROWN YELLOW VIOLET 3 BLUE ORANGE GREEN GRAY 5). 4 25mm 4 2.1.3 1). 4 Page 4 of 21 HHMC HFD1-2003 表 4 符号 含义 V 乙烯管（黑、t＝0.5） HT 耐热管 VS  乙烯树脂软片 CR 波纹管 导线管 CD Z 拉链管 S 硅清漆玻璃管 T 特利隆清漆管 U