BasiRF简析.docVIP

BasicRF 简析(四：appSwitch()简析) appSwitch()在SI中的函数关系如图1所示，其中basicRflnit()和 basicRfSendPacketO两个函数比较有内容的，木文主要针对这两个函数进行展 cRflni 11 -cRfReceiveO￡￡| -^| J b as i cR￡S endF acke t \ I ^J^pSw￡tch|- -q^JhaLlIntOnl ckPushed| I：11^ e tLowF ow er H ode | -^|aHAL_ASSERT) 开始之前先介绍三个比较重要的结构体：basicRf Rxl nfo_t、 basicRfTxState_t 和 basicRfPktHdr_t //接收帧信息 typedef struct { uint8 seqNumber; uint16 srcAddr; //中贞序号; //源地址; uint16 srcPanld; //源节点的 PANID； int8 length; uint8* pPayload //帧长度； //该指针指向帧数据即：净载荷数据 uint8 ackRequest; //巾贞控制域的皮芥位信息 int8 rssi; //接收信号强度指示; volatile uint8 isReady; //通过CRC校验，数据接收完成，该标志位进行后续 读取操作； uint8 status; } basicRfRxInfo t; //待定？ ？ ？ ？ //发送状态信息 typed ef struct { uint8 txSeqNumber; //中贞序号； volatile uint8 ackReceived; //ACK 是否接收完成; uint8 receiveOn; //是否处于接收状态； uint32 frameCounter; //发送巾贞计数； } basicRfTxState_t; //BasicRf 帧头(IEEE 802.15.4) typed ef struct { uint8 packetLength; //帧长度； uint8 fcfO; // Frame control field LSB uint8 fcf1; // Frame control field MSB uint8 seqNumber; //帧序号； uint16 panld; //PANID； uint16 destAddr; //目的地址； uint16 srcAddr; //源地址； #ifdef SECURITY_CCM //安全选项； uint8 securityControl; uint8 frameCounter[4]; #endif } basicRfPktHdr_t; (一)关于 basicRflnit() /★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★★if @fn basicRflnit * @brief Initialise basic RF datastructures. Sets channel, short address and PAN id in the chip and configures interrupt on packet reception 初始化BasicRF数据结构，如：通道选择、短地址、PANID及接收中 断的配置； @param pRfConfig - pointer to BASIC_RF_CONFIG struct. This struct must be allocated by higher layer txState - file scope variable that keeps tx state info //发送状态信 rxi - file scope variable info extracted from the last incoming frame //最新的所接 收帧信息; 收帧信息; @ return none */ uint8 basicRflnit(basicRfCfg_t* pRfConfig) { if (halRflnit()==FAILED) //Rf初始化，启用Rf的推荐简单配置 可选的PA模块配置，始终返回Success； return FAILED;hallntOff();// Set the protocol configuration pConfig = pRfConfig; rxi.pPayload = NULL;txState. receiveOn = TRUE; return FAILED; hal